The tire jack is stored in the cargo area under the floor, and you should place the jack on the reinforced pinch-weld jacking points along the rocker panels beside each wheel when lifting the vehicle.
Understanding where to find the jack and how to use the correct lifting points is essential for a safe tire change on a Honda Odyssey. Across generations, the basic layout tends to be the same: a jack kit lives in the rear cargo area under the floor (with the spare tire or a tire repair kit), and the designated jacking points are the reinforced pinch welds along the rocker panels near each wheel. Always consult your owner's manual for your exact year and trim to confirm layout and torque specs.
Where the jack and tools live in the Odyssey
Knowledge of storage locations helps you access the jack quickly when needed. The following outlines typical placements found in many Odyssey models:
- Under-floor storage: In the rear cargo area, lift the floor panel to reveal a cavity that holds the spare tire (or tire repair kit) and a modular tray containing the jack and wheel wrench.
- Tool pockets: Lug wrench and jack handle are usually stored in a pocket or tray within the same storage area or in a side bin adjacent to the spare.
Layout details can vary by generation and trim, so inspect your specific Odyssey or refer to the manual to locate the exact spots.
Where to place the jack for lifting (jacking points)
Using the correct lifting points protects the vehicle’s structure and body panels. The official jacking points are reinforced pinch welds along the rocker panels beside each wheel. Do not place the jack on plastic trim, under the bumper, or on thin underbody panels. The owner’s manual provides diagrams for your model year.
- Front jacking point: Locate the reinforced pinch weld along the front rocker panel, just beside the front wheel. Position the jack pad under this weld.
- Rear jacking point: Locate the reinforced pinch weld along the rear rocker panel, just beside the rear wheel. Position the jack pad under this weld.
- Special cases: Some generations may have a center or alternative point; always use only the points specified in your manual.
Using the designated pinch-weld points ensures a stable lift and reduces the risk of damage. If you’re unsure about the correct point for your exact year, consult the owner’s manual or a Honda technician before lifting.
Step-by-step tire change using the jack (general guidance)
Follow these general steps to change a tire safely. Adapt as needed to your Odyssey’s year and trim, and consult the manual for torque specs and any model-specific instructions.
- Park on a flat, stable surface and engage the parking brake. Chock the wheels opposite the one you’re changing.
- Loosen the lug nuts slightly while the wheel is still on the ground.
- Place the jack on the correct jacking point (front or rear pinch weld) and raise the vehicle until the tire clears the ground.
- Remove the lug nuts and the wheel. Set them aside in a safe spot.
- Mount the spare tire and hand-tighten the lug nuts.
- Lower the vehicle until the wheel just touches the ground, then fully tighten the lug nuts in a star pattern to the specified torque.
- Stow the damaged wheel, jack, and tools securely in the cargo area.
Note: If your Odyssey is equipped with a tire repair kit instead of a full spare, follow the kit’s instructions for temporary repair and inflation, then have the tire inspected and replaced as soon as possible.
Safety considerations and common mistakes
Safe lifting requires attention to surface, points, and securing the vehicle. The following guidelines help prevent accidents and damage:
- Always use the listed jacking points and never lift on plastic trim or under the bumper.
- Place wheel chocks on the opposite side and use a stable, level surface. Do not use the jack on dirt, mud, or gravel.
- Never crawl under a vehicle supported only by a jack. Use jack stands if you must work underneath.
- Avoid overtightening lug nuts; use the correct torque specification as called out in the manual.
Following these practices minimizes risk and ensures the change is completed safely and efficiently.
Summary
To change a tire on a Honda Odyssey, locate the jack and spare in the rear cargo area under the floor, then place the jack on the reinforced pinch-weld jacking points along the rocker panels beside the wheel you’re lifting. Always consult your specific year’s owner's manual for exact locations and torque specs, chock the opposite wheels, and use proper safety steps. With the right tools and points, a tire change can be completed safely and efficiently.
Where to position a tire jack?
You want to put your jack points on the flattest. Point closest to the wheel. Okay now I know it's not the same for every car but this is how it is for this car and this car is a it's a Honda Pilot.
What is the best engine oil for a Honda Odyssey?
For the 2021 Honda Odyssey EX-L, Honda typically recommends using 0W-20 full synthetic oil. This information can usually be found in your owner's manual, which should be your first stop for accurate details. The 0W-20 designation refers to the oil's viscosity, or its resistance to flow, at different temperatures.
Where is the jack for a 2011 Honda Odyssey?
After if you need to work on the engine. Department. So if you have to lift it up in the rear. There's a crossmember.
Where to place jack on Honda Odyssey?
And then you're going to use this kind of shape that your wrench has and you're going to put it right in the rod. And then you're able to turn. And then you're lifting the car. So easy right.