What size are the lug nuts on a 2012 Honda?

Most 2012 Honda models use lug nuts with a 12 mm stud diameter and a 1.5 mm thread pitch, typically with a 60-degree conical seat, and a 19 mm hex socket is usually used to remove them. This size is common across many Civics, Accords, and CR-Vs from that year, but exact specs can vary by model, trim, and wheel type. Always verify for your specific vehicle before attempting wheel work.

Below is an overview of typical specifications and a practical guide to confirm the exact size for your specific 2012 Honda, recognizing that variations can occur with trims, factory wheels, or aftermarket setups.

Typical lug nut specifications for 2012 Honda models

Before listing the common characteristics, note that these specs cover the majority of 2012 Honda passenger cars and light trucks, though there are exceptions. Use them as a baseline and verify on your vehicle when in doubt.

• Thread size: M12 x 1.50 (12 mm diameter, 1.5 mm thread pitch) for most 2012 Honda passenger cars.


• Seat type: 60-degree conical seat (the standard for many Honda wheels).


• Hex size (socket you’ll need): typically 19 mm (3/4 inch) for removal and installation.


• Variations: some trims, special editions, or aftermarket wheels may use different lug nut sizes or seat types; always verify for your exact setup.

In practice, most owners of 2012 Honda Civics, Accords, CR-Vs, and Fit models will encounter these common specifications, but there are edge cases, especially with aftermarket wheels or non-OEM replacements. If your wheels are not factory originals, the size could differ.

How to confirm the exact lug nut size for your vehicle

To ensure you have the precise lug nut size for your 2012 Honda, follow these steps:

1. Check the owner’s manual or the tire-and-wheel information label located in the driver’s door jamb; it often lists lug nut size and torque specifications.


2. Examine one of your current lug nuts for markings (some nut tops or sides indicate size or seat type) and measure the hex with a ruler or caliper to confirm the socket size.


3. Measure the lug stud diameter and pitch if needed (you can estimate the diameter with calipers; the stud is typically around 12 mm on these models, with a 1.5 mm pitch).


4. If wheels were replaced or you’re planning aftermarket wheels, consult the wheel manufacturer or a Honda parts specialist and provide your VIN for precise guidance.


5. When in doubt, contact a Honda dealership or a qualified mechanic to confirm the exact lug nut size for your specific trim and wheel configuration.

Correctly identifying the lug nut size is essential for safe installation and proper torque application. Mismatched lug nuts can lead to poor seat, wheel damage, or safety risks on the road.

Summary

For most 2012 Honda models, lug nuts are typically M12 x 1.50 with a 60-degree conical seat, and a 19 mm socket fits the nuts. However, variations can occur based on model, trim, and aftermarket wheels. Always verify with official documentation or a trusted shop before performing wheel work, and ensure you torque to the manufacturer’s specifications. If you’re unsure, a quick call to a Honda dealer or an experienced mechanic can prevent problems.

What size lug nut is on a 2012 Honda Civic?

Notes: Wheel Lug Nut -- Sold Individually; Wheel Nut M12-1.50 Acorn. 2012 Honda Civic GX.
Ask More

What size is the lug wrench on a 2012 Honda Accord?

2008-2017 Honda Accord Spare Tire Jack & Tool Kit 19mm Lug Wrench OEM #M442.
Ask More

Is 7/8 socket the same as 22mm?

A: 22mm = 0.866", which essentialy is a 7/8" socket. A 7/8" socket will work on a 22mm lug nut, but it can feel a little loose. The other way around, a 22mm can work on a 7/8" lug nut, but it can be really snug, which is not bad.
Ask More

What size of socket for to remove lug nuts Honda?

What Size Honda Lug Nuts Do I Need?