Inflate all four tires to the recommended cold pressures and drive for about 10 minutes at highway speeds; the TPMS should reset automatically. If it doesn’t, you may need to use a manual reset method if your car has one, or there could be a sensor fault.
The Tire Pressure Monitoring System (TPMS) on a 2010 Honda Accord helps alert you when tire pressure drops below the recommended level. After correcting tire pressures, the system can relearn the new pressures automatically, but some models or trims provide a dedicated reset option. This article explains both the automatic and manual approaches, as well as what to do if the light remains on.
Understanding TPMS behavior in the 2010 Accord
TPMS uses sensors in each wheel to monitor pressure. The light can come on for low pressure, a sensor fault, or after a tire is rotated or replaced. In many Accords, simply correcting the tire pressures and driving at highway speeds will cause the system to relearn the new pressures and turn the light off. Some trims or markets may include a dedicated TPMS reset button to manually trigger relearning.
Automatic reset: no button required
Before performing a manual reset, ensure every tire is inflated to the door jamb recommended pressures and then drive the car to give the system a chance to relearn automatically.
- Check all four tires when cold and inflate them to the specifications shown on the door jamb sticker (and don't forget to verify the pressures for the front and rear tires). The spare tire is usually not monitored by TPMS.
- After the tires are correctly inflated, drive the vehicle at speeds above about 30 mph (50 km/h) for at least 10 minutes to allow the TPMS to relearn the new pressures.
- Pull over and recheck the TPMS indicator. If the light has gone out, the process is complete; if it remains on, proceed to further checks.
- If the light stays on after a full relearn attempt, inspect tires for slow leaks or damage, or consider a sensor issue (a battery in a sensor can fail or a valve stem can leak).
- If needed, contact a Honda technician or tire professional to diagnose TPMS sensor readiness or a possible fault code.
The automatic relearn method is the default path for most 2010 Accords; it requires no special tool or button. If the light persists after a thorough tire pressure correction and a reasonable drive, there may be a sensor or system fault that requires service.
Manual reset: for vehicles that have a TPMS reset option
Some trims or regional variants may include a dedicated TPMS reset switch. If yours has one, use the manual reset procedure described below after confirming tire pressures are correct.
- Turn the ignition to ON (engine off) with the vehicle stationary.
- Locate the TPMS reset button (often labeled TPMS) near the steering column area, glove box, or under the dash. If your owner’s manual indicates a specific location for your trim, follow that guidance.
- Press and hold the TPMS button until the TPMS indicator in the instrument cluster blinks or a confirmation message appears, then release.
- Drive the vehicle above 30 mph (50 km/h) for about 10 minutes to allow a relearn cycle to complete.
- Check the instrument cluster to confirm the TPMS light is off. If it remains illuminated, a sensor issue or persistent underinflation may exist and require professional inspection.
Not all 2010 Accord models include a manual TPMS reset switch; many rely on automatic relearn as described above. If your vehicle does not have a reset switch, skip this section and rely on the automatic method plus tire pressure checks.
What to do if the TPMS light stays on
If the TPMS light remains on after correcting tire pressures and attempting both automatic and manual relearn methods, consider these steps:
- Check for slow leaks or punctures in any tire and repair or replace as needed.
- Inspect the valve stems for damage or loosening, which can cause leaks and trigger the sensor.
- Have the TPMS sensors tested for battery life or faults; sensors can fail or lose communication with the ECU.
- Consult a tire shop or Honda dealership for a diagnostic of TPMS sensor IDs and readiness, as some vehicles require a scan tool to relearn after a sensor replacement.
Addressing tire pressures and sensor health promptly helps ensure accurate readings and safety on the road.
Summary
Resetting the TPMS light on a 2010 Honda Accord centers on correcting tire pressures to the recommended levels and allowing the system to relearn, typically through a 10-minute drive at highway speeds. If a dedicated TPMS reset switch exists on your model, you can use it to initiate a manual relearn. If the light remains on after these steps, investigate sensor health and tire integrity, or seek professional service to diagnose and repair the system.
Where is the TPMS reset button on a Honda Accord?
Key. Then we reach down below to our tire pressure moni monitoring system switch. We push and hold for 3 seconds. And you'll see your light has gone out and the system is in the recalibration mode.
Why doesn't my Accord have a tire pressure monitor reset button?
You need to replace the sensor. And the tire dealer should be able to program those to the ECU. For you for 2013 to 2016 Honda Accord owners.
How do you reset TPMS if there is no button?
If your vehicle doesn't have a reset button, check the infotainment system or dashboard menu for a TPMS recalibration option. With the vehicle off, disconnect the battery for a few minutes to reset the system. Reconnect the battery and start the vehicle.
How to get rid of TPMS light Honda 2010?
Without Touchscreen Display
- Press “Menu”
- Select “Customize Settings”
- Select “TPMS Calibration”
- Select “Initialize”
- Select “Yes”
- Exit by selecting “Menu” again.