Most dash-light resets on the 2019 Accord are done from the instrument cluster using the SEL/RESET button. You’ll typically reset the Maintenance Minder (oil life) and the tire-pressure monitoring system (TPMS) after service or adjusting tire pressures. Some lights require professional diagnosis if they persist. This guide walks you through the common, model-accurate steps.
Understanding what you’re resetting and why
Dash warning lights cover maintenance reminders, tire pressures, and system alerts. Knowing which light you’re addressing helps ensure you reset the correct item after service or tire work. The two most common resets are Maintenance Minder (oil life) and TPMS (tire pressure).
Resetting the Maintenance Minder (oil life)
Resetting the Maintenance Minder clears the oil-life reminder after an oil change or service. The steps use the instrument cluster controls (often labeled SEL/RESET) and do not affect actual oil quality beyond what the manufacturer recommends.
- Turn the ignition to ON (do not start the engine).
- Use the selector knob or the trip button to cycle the display until Oil Life or Maintenance Minder is shown.
- Press and hold the SEL/RESET button for about 10 seconds until the oil life resets to 100% (or a confirmation message appears).
- Turn the ignition OFF, then start the engine to verify that the Oil Life shows 100% on the display.
Resetting the oil life schedules the next maintenance window according to Honda’s maintenance minder logic. If you don’t see Oil Life, look under MAINTENANCE or a gear/settings menu for OIL LIFE and reset from there.
Notes on trim variations
Some 2019 Accord trims or software versions show slightly different navigation. If Oil Life isn’t readily visible, check MAINTENANCE or the maintenance menu and select OIL LIFE from that screen.
Resetting the Tire Pressure Monitoring System (TPMS)
The TPMS warning lights indicate under- or over-inflated tires. After correcting tire pressures, you may need to reset the system so it can relearn the new pressures. Procedures can vary by trim and region.
- Ensure all tires are inflated to the recommended cold pressures listed on the door placard, and reinstall valve caps securely.
- With the vehicle in Park and the ignition ON, drive at a moderate speed (roughly 40–50 mph) for several minutes. The TPMS light should either turn off automatically or indicate a successful reset.
- If your model supports a manual TPMS reset, navigate to Vehicle Settings > TPMS > Reset (or Store TPMS Values) on the information display and confirm. The system may beep or show a confirmation message.
Note: In many cases, the TPMS will reset automatically after proper tire inflation and a short drive. Manual resets are most often needed after replacing tires or sensors or on certain trims.
Other dash lights and cautions to know
Other warning lights (check engine, ABS, airbags, etc.) may indicate genuine faults rather than a simple reset. A persistent or flashing light should be diagnosed by a qualified technician. If a light remains after attempting the standard reset, consult the owner's manual for your exact trim or contact a Honda service center.
What to do if a light won’t reset
If a light stays on after following these steps, it may indicate a condition that needs repair or monitoring. Check for available service bulletins, reread the manual, and consider a scan with an OBD-II tool or professional diagnostic help to identify underlying codes or issues.
Summary
For a 2019 Honda Accord, most dash-light resets fall into two categories: Maintenance Minder/oil life resets and TPMS resets. Reset the Maintenance Minder by displaying Oil Life and holding the SEL/RESET button until it resets to 100%. Reset TPMS after inflating tires to the correct pressures, either automatically by driving or via a manual reset option if your trim supports it. Remember that other warning lights require diagnosis and repair rather than a simple reset. If uncertain, consult the owner’s manual for your exact trim and software version.
How to reset warning lights on 2019 Honda Accord?
And then scroll up again until you see maintenance info. I have very services that I did on my vehicle. So I'm going to select reset items. And I am going to select all due items.
How to reset Honda dashboard warning lights without scanner?
How to Reset Honda Check Engine Light
- Turn off the ignition.
- Locate the negative terminal.
- Loosen the nut on the negative terminal with a wrench.
- Reconnect the negative cable and tighten it back up with your wrench.
- This should reset the check engine light for your Honda car.
How do you reset the dash lights on a Honda Accord?
Okay as you can see the service A is starting to flash. We're going to let off. And then we're going to press and hold this button. Again. So right there our oil life is reset up to 100%.
How do I reset my dashboard warning lights?
Disconnecting the Car Battery
If you don't have a scanner, this old-school method might work. Turn off the ignition and open the hood, then use a wrench to disconnect the negative battery cable. Wait about 15 minutes, then reconnect the battery cable and tighten it securely. Start the car to see if the CEL has reset.