How do you fix the TPMS light on a Honda?

The Tire Pressure Monitoring System (TPMS) light on a Honda typically goes off after tires are properly inflated and the system is relearned. In most cases, inflate the tires to the vehicle’s recommended pressure, then perform a TPMS reset or relearn; if the warning persists, a faulty sensor or tire issue may be involved.

Check and correct tire pressures

Begin by verifying all four tires are inflated to the recommended cold pressure for your specific model. Use the door jamb sticker or the owner's manual to confirm the correct PSI, and check when the tires are cold.

• Find the recommended cold tire pressure (PSI) for your model on the door jamb sticker or in the owner's manual.


• Check all four tires with a digital gauge when the tires are cold; temperature can affect readings, so measure before driving.


• Inflate each tire to the recommended PSI. Do not exceed the maximum listed on the tire sidewall; if a tire won’t hold pressure due to damage, repair or replace it.


• Recheck all four tires after inflation and monitor for any sudden pressure loss in the following days.

After inflating to the specified pressures, the TPMS light should either go off on its own after a short drive or prompt you to perform a relearn if your model requires it.

Resetting or relearning the TPMS on a Honda

Many Hondas require a relearn procedure after inflating tires or changing tires. Procedures vary by model and year, so consult your owner’s manual. Here are common approaches used by many Honda models:

1. Drive at about 50 mph (80 km/h) for 10 minutes or longer to allow the system to relearn the new pressures automatically.


2. If your Honda has a TPMS button, locate it (often near the glove box, under the dash, or on the instrument panel). With the ignition on and the engine off, press and hold the TPMS button until the indicator light blinks, then release. Drive to complete the relearn.


3. In some newer Hondas, access Settings or Vehicle on the infotainment display to choose TPMS Relearn or Reset, then follow on-screen prompts and drive at steady speeds to complete the relearn.


4. If the light remains on or flashes after the relearn attempt, there could be a failed sensor or tire leak. Consider professional testing or sensor replacement.

Properly performing a relearn typically resolves the warning after the tires are inflated correctly and the system has registered the new pressures.

When to service or replace TPMS sensors

TPMS sensors (one per wheel) can fail due to battery depletion, damage, or moisture ingress. If the TPMS light stays on after successful inflation and relearn, you may need sensor service or replacement.

• Common signs of sensor issues: the light stays on even after inflating to spec, or it refuses to turn off after driving. A fluctuation with speed can indicate sensor communication problems.


• Sensor lifespan: many TPMS sensors last roughly 5–10 years, but batteries can die sooner in harsh temperatures.


• What a shop can do: diagnose with a handheld TPMS scanner, replace faulty sensors, and reprogram them to the vehicle. This often requires removing the tire from the wheel.

Note: If you recently replaced a tire, a TPMS relearn is typically required for the new sensor or wheel to be recognized.

Model-specific notes

Because Honda model years and trims vary in TPMS reset and relearn methods, use this as a guide and consult your owner’s manual or a dealer for the exact steps for your car.

Common procedures by group

These are representative methods you may encounter across different Hondas:

• Older Hondas (late 2000s and earlier) often use a dedicated TPMS reset button located under the steering column or inside the glove box.


• Most 2014–2019 Honda models use a combination of inflating tires to spec and either driving at highway speeds or using the vehicle settings menu to trigger a relearn.


• Recent models (2020s) may require selecting TPMS Relearn in the infotainment or driver information display; you still need to have the tires inflated to spec before starting the relearn.

Always refer to the exact procedure in your manual; if in doubt, a dealership or qualified tire shop can perform a TPMS relearn for you.

Summary

Bottom line: start by ensuring all four tires are at the correct cold pressures, then perform the relearn procedure as required by your model. If the light stays on, or if it flashes, the system may have a faulty sensor or a leak, and professional service will be needed. Regularly checking tire pressure—at least monthly and before long trips—helps prevent TPMS warnings and keeps tires safer and more efficient.