Yes. On most Honda Accords, you reset the TPMS by inflating all tires to the recommended cold pressures and then using the built‑in TPMS learn procedure (either with a dedicated TPMS button or by driving at highway speeds for a short period) to relearn the sensors.
Understanding TPMS on the Honda Accord
The Tire Pressure Monitoring System (TPMS) in modern Honda Accords uses sensors in each wheel to monitor air pressure. When tires are inflated to the recommended cold pressures, or after tires are rotated or replaced, the system may need to relearn the sensor IDs so the warning light reflects actual conditions. The exact relearn method can vary by model year and trim, so consult your owner’s manual if you’re unsure.
When you should reset TPMS
Resetting or relearning is typically needed after you:
- Inflate tires to the door‑jamb specification after a recent service or replacement.
- Rotate tires or replace wheels or sensors.
- Repair a slow leak or replace a tire with a new one.
- Notice the TPMS warning light staying on even when pressures are correct.
Resetting is usually a straightforward process, but the exact steps can depend on your model year and trim level. If you don’t see a TPMS button or the light behavior doesn’t match the described steps, check the owner’s manual or contact a Honda dealer.
Step-by-step reset procedure (typical method)
Follow these steps for most late‑model Accords with direct TPMS. If your car doesn’t show a Learn button or use a drive‑to‑learn method, skip to the alternative approach below.
- Verify all four tires are inflated to the recommended cold pressures listed on the driver’s door jamb sticker or in the manual.
- If your Accord has a TPMS Learn button (often located near the steering column, under the dash, or in the glove box), turn the ignition to ON with the engine OFF and press and hold the Learn button until the TPMS indicator light either blinks or the dashboard shows a Learn message. Release the button.
- Drive the vehicle at a steady speed (typically around highway speeds) for about 10 minutes to complete the relearn process. The exact time can vary by year and trim.
- Turn the ignition OFF, then back ON and check whether the TPMS warning light goes out. If it stays on, verify pressures again and repeat the relearn steps if needed.
- If you replaced sensors or rims, or if the light remains after recheck, a professional diagnostic using the proper TPMS tool may be required to complete or reprogram the relearn.
The exact button location and timing can differ by model year and trim, so if you don’t see a Learn button or the light behavior differs, refer to your owner’s manual or contact a dealer for model‑specific instructions.
Alternative relearn methods (no Learn button)
Drive-to-learn method
If your Accord lacks a Learn button or the button procedure doesn’t apply, you can often relearn by driving the vehicle after inflating to spec. Maintain steady speeds on highways and roads for a set period (commonly around 10–20 minutes) to allow the sensors to register and complete the relearn process.
Professional tools and dealer service
Some younger or higher‑trim models may require a scan tool or dealer‑level equipment to relearn TPMS sensors, especially after sensor replacement or complex tire work. In these cases, visiting an authorized Honda service center or a trusted tire shop ensures proper programming and sensor registration.
Note: If you’ve recently rotated tires or replaced sensors and the light stays on, it’s a good sign the system needs to relearn. If it never goes out after following these steps, there may be a faulty sensor or a leak that needs repair.
Troubleshooting and tips
These quick tips help prevent false warnings and ensure a smooth relearn experience.
- Always check tire pressures when the tires are cold to get an accurate reading.
- Inspect tires for visible damage or slow leaks that could cause persistent low pressure.
- Ensure the valve stems and sensors are not damaged during tire service or wheel changes.
- If you replace a sensor, confirm all four sensors are recognized by the vehicle during the relearn process.
- Keep the owner's manual handy for model‑specific steps, as procedures can vary by year and trim.
If you still see a TPMS warning after attempting the relearn, consider visiting a Honda dealer or a tire shop with TPMS calibration equipment to diagnose sensor health and perform a professional relearn.
Summary
Resetting the TPMS on a Honda Accord generally involves inflating all tires to the recommended cold pressures and then performing a relearn using either a TPMS Learn button (if equipped) or a drive‑to‑learn method. The exact steps depend on the model year and trim, so consult the owner’s manual or a dealer if you’re unsure. After a successful relearn, the TPMS light should go out; if not, there may be a faulty sensor or a leak requiring professional service.
How do you reset your Honda's Tire Pressure Monitoring System TPMS?
With Touchscreen
- From the Home screen, select “Settings”
- Select your vehicle.
- Select “TPMS Calibration”
- Select “Calibrate”
Why is my Honda Accord inflated tire still showing tire low pressure?
One of the most common reasons for a TPMS light staying on despite the tires being properly inflated is a sensor malfunction. TPMS sensors are typically located inside the tire and can wear out or become damaged over time, particularly if you've hit a curb, driven through a pothole, or been off-road.
Where is the TPMS reset button on a Honda Accord?
So you're going to do it through this screen right here click your home button we're already on home go to settings. Go to vehicle. Choose your first option TPMS calibration. And then click calibrate.
Why doesn't my Accord have a tire pressure monitor reset button?
You need to replace the sensor. And the tire dealer should be able to program those to the ECU. For you for 2013 to 2016 Honda Accord owners.