Where is the oil filter in a 2014 Nissan Altima?

The oil filter location on a 2014 Altima depends on the engine: the 2.5-liter four-cylinder uses a cartridge-style filter mounted on the passenger side of the engine block, while the 3.5-liter V6 uses a conventional spin-on filter at the front of the engine. Access typically requires removing the front undertray or shield and working from beneath the vehicle.

Engine options and filter types

In 2014, the Altima offered two main powertrains. Understanding which engine you have will tell you where to look for the oil filter and what kind of filter you’ll replace during an oil change.

2.5L four-cylinder (QR25DE)

The 2.5L engine uses a cartridge-type oil filter that sits inside a plastic housing on the passenger side of the engine block. It is not a traditional screw-on canister that you see on many older engines. Access is usually easiest from underneath the car after removing the front splash shield.

Tools and steps to locate and inspect the 2.5L filter:

• Park on a level surface, engage parking brake, and raise the front of the car safely.


• Remove the undercar splash shield to expose the lower engine area.


• Locate the oil-filter housing on the passenger side of the engine block.


• Open the housing cap to reveal the cartridge filter inside (not a spin-on canister).

Conclusion: For the 2.5L Altima, expect a cartridge-style filter inside a housing on the passenger side of the engine, accessible from below with the shield removed.

3.5L V6 (VQ35DE)

The 3.5L V6 uses a conventional spin-on oil filter mounted on the front of the engine. It is typically easier to access from above with the hood open, though some variations may require working from underneath after removing the shield or components that block access.

Tools and steps to locate and inspect the 3.5L filter:

• With the hood up, look toward the front of the engine for a standard metal canister with an end-cap.


• The filter is usually located near the front-center of the engine bay, close to the belt or pulleys area.


• Use the appropriate filter wrench to loosen the canister cap and inspect the seal and condition.

Conclusion: The 3.5L Altima uses a traditional spin-on oil filter located at the front of the engine, generally accessible from the top or bottom once shielding is managed.

How to access and replace the filter (overview)

Whether you have the 2.5L or the 3.5L engine, follow these general steps to replace the oil filter and perform an oil change. Always consult the owner’s manual for the exact oil type, capacity, and service intervals.

Steps for the 2.5L engine

Before starting the list, ensure you have the right filter cartridge, a suitable oil, a drain pan, and basic hand tools. The following is a typical procedure for the cartridge-type setup.

• Warm the engine briefly and safely lift the front of the car, placing it on stands.


• Remove the front splash shield to access the oil-filter housing on the passenger side.


• Unseal and remove the housing cap, then extract the old cartridge.


• Install a new cartridge and reseal the housing cap with a new O-ring if provided.


• Reinstall the housing cap, lower the car, and refill oil to the proper level.

Conclusion: Replacing the cartridge-type filter on the 2.5L involves accessing a housing on the passenger side of the engine and swapping the internal cartridge rather than unscrewing a spin-on canister.

Steps for the 3.5L engine

Before proceeding, confirm you have the correct spin-on filter and an oil drain pan, as well as safety equipment. The typical replacement process is straightforward for a conventional canister filter.

• Raise the vehicle or position yourself safely to access the front of the engine.


• Place a drain pan beneath the filter, then loosen and remove the old canister with a filter wrench.


• Apply a light film of oil to the gasket on the new filter, install it hand-tight, then snug with the wrench per manufacturer specs.


• Reinstall any shields or components removed for access, refill with the recommended oil, and check for leaks.

Conclusion: The 3.5L engine uses a standard spin-on filter that is typically accessible from the front, with shield removal sometimes required for full clearance.

How to identify your engine if you’re not sure

If you’re uncertain which engine is in your 2014 Altima, check the VIN sticker on the door jamb or consult your owner’s manual. The engine code printed in the engine bay will confirm whether you have the 2.5L four-cylinder or the 3.5L V6, which in turn determines the filter type and location you should expect.

Summary

For a 2014 Nissan Altima, the oil filter location depends on the engine. The 2.5L four-cylinder uses a cartridge-style filter housed on the passenger side of the engine block, usually accessed from beneath after removing the splash shield. The 3.5L V6 uses a conventional spin-on filter mounted at the front of the engine, generally accessible from the top or bottom with appropriate shield clearance. Always verify the engine type and refer to the owner’s manual for exact specifications, oil type, and service intervals.

What's the fastest Altima?

2021 Altima Engine Performance

Where is the oil filter on a Nissan Altima?

While the oil drains, you can access the oil filter in the passenger fender well by removing the push clips on the panel covering it, and moving the panel aside. Position shop towels or rags below the filter before you unscrew it.

Where is the oil filter located in a 2014 Nissan Altima?

So if you don't have the ability to torque it just do your best to squish that washer without overtightening. It through the passenger side wheel well you can see the oil filter located on the side of

Where is the oil filter located on a Nissan?

Remember that there is also oil in that. So um as you loosen it you don't want it to kind of just spill down your arm. And make sure that the pan is also under that when you loosen. It.