The 2017 Chrysler Pacifica uses 0W-20 synthetic motor oil. This applies to the gas-powered 3.6L V6 and the 2017 Pacifica Hybrid, per Chrysler's specifications.
In detail, this guidance covers both engine variants available in that model year. Use a 0W-20 full-synthetic oil that meets API SN or newer and ILSAC GF-5 or GF-6 standards, and, where applicable, Chrysler MS-6395 approvals. The typical oil capacity is roughly 5–6 quarts with a filter, but always consult your owner's manual or the under-hood label for the exact figure for your specific build date and trim.
Key oil specifications to follow
Before listing the essential oil requirements, here are the core standards to check when shopping for oil for your Pacifica.
- Grade: 0W-20 synthetic motor oil (full synthetic is preferred).
- Standards and approvals: API SN or newer; ILSAC GF-5 or GF-6 compatible; Chrysler MS-6395 approval is commonly recommended for Mopar engines.
- Capacity: roughly 5–6 quarts with filter, depending on the exact engine variant; verify with the manual for your vehicle.
Conclusion: Use oil that meets these specifications to ensure proper lubrication, performance, and warranty compliance.
How to verify your exact specification
To confirm the precise oil requirement for your vehicle, follow these practical checks.
- Consult the owner's manual's Engine Oil section for grade, spec, and capacity.
- Inspect the oil filler cap on the engine for any grade markings (some caps indicate 0W-20).
- Look for the under-hood label near the engine bay that lists the recommended oil grade and capacity.
- If in doubt, use your VIN to fetch exact specifications from Mopar/Chrysler portals or ask your dealership to confirm the 0W-20 requirement and MS-6395 approval for your build date.
Conclusion: For most 2017 Pacifica models, the recommended oil is 0W-20 synthetic; exact capacity and any variant-specific notes should come from the manual or dealer.
Maintenance and change intervals
Understanding the right interval helps protect the engine when using 0W-20 synthetic oil.
- Normal driving: around 7,500 miles (12,000 km) between changes, or as indicated by the vehicle’s maintenance minder.
- Severe driving conditions: about 3,000–5,000 miles (5,000–8,000 km) between changes.
- Always check the oil level regularly and top up as needed, using the correct grade if you add oil between changes.
Conclusion: Adhere to the maintenance schedule provided by Chrysler and use the specified 0W-20 oil to maintain engine protection and efficiency.
Summary
For the 2017 Chrysler Pacifica, use 0W-20 synthetic oil that meets API SN or newer and ILSAC GF-5/GF-6 standards, with a typical capacity of about 5–6 quarts (plus filter). This guidance applies to both the gas 3.6L V6 and the Pacifica Hybrid. Always verify with the owner's manual or your dealer for the exact specification and capacity for your specific build date and configuration.
What oil is recommended for a 2017 Chrysler Pacifica?
Pennzoil – Platinum 5W-20 Full Synthetic Motor Oil, Maximizes Engine Protection, 5 Quart (Part No. 550046122)
How much oil does a 2017 Chrysler Pacifica 3.6 L take?
5 quarts
Oil Grade: SEO11
| Viscosity: | 0W-20 (All TEMPS) |
|---|---|
| Capacity: | 5 quarts (with filter). After refill check oil level. |
| Torque: | 20 ft/lbs (Oil Drain Plug) |
Can I use 5W30 instead of 5W20 in my Chrysler?
Only switch if your owner's manual approves. Using the wrong oil can affect engine performance and longevity. Moving from 5W20 to 5W30 adds protection but might reduce efficiency. Going from 5W30 to 5W20 could lessen engine protection, especially during Lansing's temperature extremes.
What type of oil does a 3.6 L V6 take?
3.6L V6: SAE 0W-20 Full Synthetic (API Starburst) — 5 quarts with filter.