For most Honda CR-V models, lug nuts use M12 x 1.5 threaded studs with a 19mm hex socket, but exact specifications can vary by year, trim, and wheel setup. This article explains the standard size, how to verify your specific vehicle, and best practices for installation.
Standard lug nut size across modern CR-Vs
To understand what you’ll typically encounter on contemporary CR-Vs, consider the most common specifications that appear across recent generations.
- Thread size: M12 x 1.5 (metric, standard on most CR-Vs from the 2000s onward)
- Nut seat: 60-degree conical (acorn) seating
- Socket size: 19mm across flats for the lug nuts
- Notes: Some aftermarket wheels or locking lug nuts may require different hardware or socket sizes; always verify for your setup
These specifications cover the majority of Honda CR-V models built in the 2000s through the present, but wheels and trims can introduce variations. Always confirm with your vehicle’s manual or the wheel manufacturer if you’re unsure.
How to verify the exact size for your CR-V
Because wheel and lug nut configurations can differ by year and option packages, use these steps to confirm the precise size for your vehicle.
- Check the owner's manual or service manual for the recommended lug nut size and torque spec
- Inspect a lug nut on your wheel for stamped information (look for M12 x 1.5 and seating type)
- Measure the lug nut with a caliper or use a lug nut sizing tool to confirm thread and seat
- Confirm wheel specifications if you use aftermarket wheels or lug nuts
- When in doubt, contact a Honda dealer or the wheel manufacturer for a definitive specification
Verifying the exact size before purchasing replacements helps prevent damage to studs, wheels, or the lug nuts themselves and ensures proper fitment and safety.
Torque and installation tips
Proper torque and installation practices are essential for safety and wheel longevity. Use these guidelines as a baseline, then consult your year-specific manual for any deviations.
- Typical torque: about 80–85 ft-lb (108–115 Nm)
- Always torque in a crisscross (star) pattern to ensure even seating of the wheel
- Re-torque after a short drive or 50–100 miles to account for settling
- Avoid applying anti-seize compounds on lug studs unless the manual specifies otherwise
Following proper installation practices helps maintain wheel integrity and road safety. If you’re unsure about torque specs or seating, have a professional service technician verify the installation.
Year-by-year quick reference (general guideline)
The most common configuration for recent Honda CR-V generations is M12 x 1.5 with a 60-degree conical seat and a 19mm socket. However, always verify your specific year, trim, and wheel setup to avoid mismatches or damages.
Summary
In short, the typical lug nut size for most Honda CR-V models from the 2000s onward is M12 x 1.5 with a 60-degree conical seat and a 19mm wrench size. Always confirm your exact vehicle’s lug nut size by consulting the owner's manual, inspecting the current lug nuts, or checking with a dealer or wheel manufacturer—especially if you’ve upgraded wheels or are dealing with a special edition. Accurate verification ensures safe installation and proper wheel performance.
What size of socket for to remove lug nuts Honda?
What Size Honda Lug Nuts Do I Need?
| Model | Year | Thread/ Socket Size |
|---|---|---|
| CR-V | 1997-2020 | 19 mm |
| Pilot | 2003-2020 | 21 mm |
| Odyssey | 2003-2020 | 21 mm |
| Ridgeline | 2006-2020 | 21 mm |
What size socket for Honda CR-V lug nuts?
Honda CRV Lug Nuts Sizes
The lug nuts on most Honda CR-V models from 1997-2025 are 12×1.5 mm with a torque spec of 80 ft-lbs. This means you'll need a 19mm socket to remove or install the lug nuts.
What size lug nuts does a Honda CR-V use?
Dorman – Wheel Lug Nut: M12-1.50 Thread, Conical 60, Bulge Acorn, 1.382" Length, Chrome (sold by each) (Part No. 611-182) Wheel Lug Nut (M12-1.50) offers a seamless fit and dependable performance, making it an ideal direct replacement for original equipment hardware on specified vehicles.
Is 7/8 socket the same as 22mm?
A: 22mm = 0.866", which essentialy is a 7/8" socket. A 7/8" socket will work on a 22mm lug nut, but it can feel a little loose. The other way around, a 22mm can work on a 7/8" lug nut, but it can be really snug, which is not bad.