The 2016 Chrysler 200 uses synthetic motor oil, with 0W-20 being the typical factory-grade recommendation. Exact specifications depend on which engine your car has (2.4L Tigershark I4 or 3.6L Pentastar V6) and the climate, but you should always use oil that meets the manufacturer’s specifications and service manual guidance.
This article outlines the engine options for the 2016 Chrysler 200, the recommended oil types and viscosities for each, typical oil capacities, and practical tips for choosing a brand or formulation to keep your engine running smoothly and within warranty requirements.
Engine options and oil specifications
Below are the two engines offered in the 2016 Chrysler 200 and their corresponding oil guidance.
2.4L Tigershark I4
Recommended oil: Synthetic motor oil meeting API SN Plus and ILSAC GF-5 (GF-6 compatible). Preferred viscosity is 0W-20; 5W-20 is acceptable if 0W-20 is not readily available. Capacity: approximately 4.5–4.7 quarts (with filter). Use a quality full-synthetic oil to maximize protection and fuel efficiency.
3.6L Pentastar V6
Recommended oil: Synthetic motor oil meeting API SN Plus and ILSAC GF-5 (GF-6 compatible). Preferred viscosity is 0W-20; 5W-20 can be used if 0W-20 is unavailable. Capacity: about 5 quarts (with filter). As with the 2.4L, choose a high-quality full-synthetic oil.
Both engines share a common emphasis on high-quality synthetic oil that meets contemporary API and ILSAC specifications. Always verify the exact specification in your owner’s manual or on the under-hood label specific to your vehicle, since production changes or regional recommendations can alter the precise requirement.
Oil brands and formulation tips
When selecting oil, aim for products that clearly meet the listed specifications and consider using OEM-recommended or OEM-approved formulations. The guidance below helps ensure compatibility and warranty protection.
Use a full-synthetic motor oil that meets API SN Plus and ILSAC GF-5 (GF-6 compatible) requirements, as appropriate for your engine and climate.
If you prefer a branded option, choose well-known synthetic brands that offer 0W-20 or 5W-20 viscosity in their high-quality lineup; ensure the product specifies compatibility with FCA/M Chrysler services and the engine in your 2016 Chrysler 200.
Mopar-approved or OEM-listed filters are recommended to ensure proper fit and filtration for your oil change interval.
In practice, you’ll typically be buying 0W-20 synthetic oil for these engines, with 4.7–5 quarts capacity depending on engine and whether you replace the oil filter. Always use the correct filter and torque specs during a change, and don’t mix used oil types during a single drain-and-fill.
Maintenance and change intervals
Oil change intervals for the 2016 Chrysler 200 generally align with the vehicle’s maintenance schedule, typically around every 5,000 to 7,500 miles under normal driving conditions when using synthetic oil. In severe driving conditions (short trips, extreme temperatures, towing, or dust-heavy environments), more frequent changes may be advised. Always follow the service manual’s recommended interval and reset the oil life monitor after each change.
Conclusion and practical takeaways
For a 2016 Chrysler 200, use synthetic oil that meets API SN Plus and ILSAC GF-5/GF-6 standards, with a viscosity of 0W-20 as the primary option (5W-20 is acceptable if 0W-20 is unavailable). The 2.4L engine typically requires about 4.5–4.7 quarts, while the 3.6L engine requires roughly 5 quarts. Always consult the owner’s manual for your exact engine and regional guidelines, and consider OEM-recommended filters and brands to maintain performance and warranty compliance.
Summary
The 2016 Chrysler 200’s oil guide centers on synthetic 0W-20 (with 5W-20 as a fallback if needed), meeting API SN Plus and ILSAC GF-5/GF-6 standards. Engine capacity differs by 2.4L or 3.6L variants, but both emphasize high-quality synthetic oil and proper filtration. Regular changes per the manual help protect engine longevity and efficiency.
Can you put 5W-30 in a Chrysler 200?
6 Liters Of German RAVENOL DXG 5w30 Motor Oil - Meets the Chrysler MS-6395 motor oil quality standard and viscosity required for the 3.6L Chrysler 200 gasoline engine.
How much oil does a 2016 Chrysler 200 take?
Oil Grade: SEO11
| Viscosity: | 0W-20 (All TEMPS) |
|---|---|
| Capacity: | 5.8 quarts (with filter). After refill check oil level. |
| Torque: | 20 ft/lbs (Oil Drain Plug) |
What is the best oil for a 2016 Chrysler 200?
6 Liters of Fully Synthetic Eurol Evolence 0W20 Motor Oil - Meets or exceeds the recommended Chrysler MS-6395 oil quality specification and performance characteristics required for the Chrysler 200 2.4L Tigershark MultiAir 4-cylinder engine.
What type of oil does a Chrysler 200 use?
5W-20
6 liters 5W-20 Chrysler 200 motor oil, oil filter, and hardware for 3.6L 24V V6 applications. Meets Chrysler MS-6395 motor oil quality standards.