In short: the 2007 Honda Accord uses a standard spin-on oil filter, and the exact part depends on which engine you have—the 2.4-liter four-cylinder or the 3.0-liter V6. Use Honda’s genuine filter or a reputable aftermarket equivalent that fits the engine’s specifications.
The 2007 Accord came with two available powertrains in many markets: a 2.4L inline-four and a 3.0L V6. Both use the conventional spin-on oil filter design rather than a cartridge. To ensure you get the right filter, identify your engine code (K-series for the 2.4L or J-series for the 3.0L) and verify the exact part number with an auto parts counter or your vehicle’s documentation. The following guidance summarizes how to choose the correct filter and what to consider when buying replacements.
Engine options and filter type
To help you identify which filter fits, here are the two engine options commonly found in the 2007 Accord and how they relate to the filter:
- 2.4L four-cylinder engine (K-series): Uses Honda’s standard spin-on oil filter; you can choose the OEM Honda filter or a high-quality aftermarket equivalent that matches the engine’s thread size and gasket specification.
- 3.0L V6 engine (J-series): Also uses a conventional spin-on oil filter with the same general fitment requirements; verify the exact part number to ensure compatibility with your VIN and engine code.
In both cases, aftermarket filters from brands such as Wix, Bosch, Purolator, and Fram are commonly available and designed to fit the same thread size and sealing surface as the OEM filter. Always confirm fitment for your specific engine code and model year before purchasing.
Choosing the right filter: OEM vs aftermarket
Before buying, consider your preferred option and the level of guidance you want from retailers. OEM filters guarantee Honda-specified filtration performance, while aftermarket options often provide comparable performance at a lower cost. What matters most is matching the thread size, gasket diameter, and filtration rating to your engine’s requirements.
- OEM Honda filter: The safest choice for fit and filtration; widely available at Honda dealers and parts stores.
- Quality aftermarket filters: Choose brands with a solid reputation for automotive filtration and confirm compatibility with the 2.4L or 3.0L engine.
- Filtration rating and flow: Ensure the replacement offers a compatible flow rate and filtration efficiency for your engine oil capacity and driving conditions.
- VIN-based cross-reference: If you’re unsure, provide the VIN to the parts counter to receive the exact cross-reference for your car.
By verifying the engine code and using a filter designed for the appropriate engine, you’ll maintain proper oil pressure and engine protection between changes.
Replacement steps
Here are the general steps to replace the oil filter on a 2007 Accord. If you’re not comfortable performing maintenance, consider letting a professional handle the job.
- Warm up the engine briefly, then turn it off and secure the vehicle on a level surface with the parking brake engaged.
- Drain the engine oil into a suitable pan by removing the drain plug, then replace the plug once the oil has finished draining.
- Place a drain pan under the filter, use a filter wrench to loosen and remove the old filter by turning counterclockwise.
- Prepare the new filter: apply a light coat of fresh engine oil to the gasket on the top of the new filter.
- Install the new filter by hand until it seats firmly, then snug it an additional quarter turn (do not overtighten).
- Refill the engine with the recommended amount and type of oil for your engine, then start the engine and check for leaks.
- Shut off the engine, wait a moment, and recheck the oil level; add oil as needed to reach the proper level.
Following these steps helps ensure a clean swap and proper sealing to prevent leaks once you start the engine again.
Verifying compatibility and where to buy
How to verify compatibility
To be certain you’re buying the right filter, check the engine code on your vehicle (found under the hood or in the owner's manual) and compare it with the part information provided by the parts supplier. If in doubt, use your VIN when shopping to receive the precise cross-reference for your car’s exact configuration.
Shopping options include local auto parts stores, Honda dealerships, and reputable online retailers. Always confirm fitment for your specific vehicle before purchasing, especially if you’re ordering online.
Summary
The 2007 Honda Accord uses a conventional spin-on oil filter, with two possible engine options requiring you to confirm the specific part number for your model. Whether you choose an OEM Honda filter or a trusted aftermarket option, the key is to ensure correct fitment for your engine code and to follow proper replacement steps to maintain engine health.
For ongoing maintenance, keep track of your oil change intervals as recommended in the owner’s manual and replace the filter during every oil change to ensure optimal filtration and engine longevity.
What size oil filter for a 2007 Honda Accord?
4L L4 Gas Oil Filter.
What does the PH7317 oil filter fit?
Broad Compatibility: The PH7317 filter fits a wide range of Honda, Subaru, Nissan, and Acura vehicles from 2001 to 2023.
What oil filter does a Honda Accord take?
15400-PLM-A02) Genuine Honda original equipment oil filter for your Honda vehicle. Engineered and specified by Honda, this is the same filter as that which would be installed by your dealer.
What is the OEM oil filter for a 2007 Honda Accord?
This OEM Honda oil filter, part number 15400-PLM-A02, fits select Honda vehicles from model years 2000 all the way to 2021. Its job is to collect both the impurities in motor oil and whatever else accumulates as the oil lubricates engine parts.