For the 2014 Honda CR-V, the fog light uses a standard H11 halogen bulb (12V, about 55W). This is the common specification across most trims, though regional differences and aftermarket setups can vary, so it’s wise to verify before purchasing.
In this article, we outline the bulb type, how to confirm the exact bulb in your vehicle, and the typical replacement steps. We’ll also touch on considerations if you plan to swap to LEDs or HID kits.
Bulb type and compatibility
The fog lights on most 2014 CR-Vs are designed for H11 bulbs. The H11 base is a 12-volt, 55-watt halogen design widely used by manufacturers. If you are replacing the bulb, ensure you buy an H11 with the correct polarity and wattage. If you have an aftermarket LED or HID kit, check compatibility and consider anti-flicker devices or CAN bus modules to avoid warning lights or electrical issues.
Note that a few markets or trims may have variations, so when in doubt, check the bulb marking inside the fog light housing or consult the owner's manual or dealership for confirmation.
Is it possible to upgrade or change to LED?
Upgrading to LED or HID in fog lights is a common customization, but it isn’t always straightforward. LED bulbs may require a CAN bus adapter, a resistor to prevent flicker, and a proper heat management solution. HID kits may require ballast and can also trigger error codes if the vehicle's computer detects out-of-spec lighting. If you choose to upgrade, consider professional installation to ensure proper fitment and electrical compliance.
Always verify compatibility with your specific vehicle and region before buying upgrades.
How to replace the fog light bulb
If you plan to replace the bulb yourself, follow these steps. The process is typical for 2014 CR-V models with H11 fog bulbs, though layout can vary by region or trim. Make sure you have the correct bulb and the vehicle is safely secured.
- Park on level ground, switch off the engine, and engage the parking brake. For extra safety, disconnect the negative battery terminal before working near electrical connections.
- Gain access to the fog light housing. Depending on trim and bumper design, you may need to remove the front bumper cover, a splash shield, or an access panel to reach the fog light assembly.
- Detach the electrical connector from the back of the fog light bulb by pressing the release tab and pulling it straight out.
- Remove the bulb retainer or rotate the bulb counterclockwise (as applicable) to free the bulb from the housing.
- Install the new H11 bulb, ensuring the alignment tabs engage properly. Reconnect the electrical connector.
- Test the fog light by turning on the headlights and fog lights before reassembling any panels, then secure any removed parts.
Following these steps should allow you to replace the H11 fog light bulb without damaging the housing or wiring. If the bulb does not light after replacement, recheck the connector and fuses, or seek professional service.
Additional notes
LED or HID upgrade considerations
LED or HID replacements can improve brightness, but they may require adapters, ballast, or CAN bus modules to avoid electrical issues. Compatibility with the vehicle’s electrical system and legal regulations in your area should be verified before attempting upgrades. If unsure, consult a qualified technician.
Summary
The 2014 Honda CR-V fog lights use H11 bulbs (12V, about 55W). Replacement is straightforward but may require access through the bumper or splash shield. Upgrading to LEDs or HIDs involves additional considerations and potential adapters to maintain proper operation and safety.
What bulb does a 2014 Honda CRV take?
Honda CR-V (2012-2014) Bulb Size Chart
| Headlights (High Beam and Low Beam) | H4 (9003 HB2) |
|---|---|
| Side Marker Light (Front) | T10 (194 168) |
| Turn Signal Light (Front) | 1157 (BAY15D) |
| License Plate Light | T10 (194 168) |
| Lower Tail Light | 7443 (7440) |
What size bulb is the fog light on a Honda CRV?
Honda CR-V Bulb, Foglight (H11) (12V 55W) (Valeo)
How to replace fog lights on a Honda CRV 2014?
You know it's just a trim piece that's plastic. And it helps to pry from the outside to the inside. It's got little tabs that kind of push. Out.
Can I use H11 for fog lights?
H11 LED BULBS | HEADLIGHT AND FOG LIGHT BULB REPLACEMENTS
Upgrading your vehicle to H11 LED Bulbs significantly increases the light output of your headlights or fog lights.