Inflate all tires to the recommended cold pressures and then reset the TPMS either with the dedicated reset button or by allowing an automatic relearn as you drive. The exact steps vary by model and year, so check your owner's manual for model-specific instructions.
What the TPMS light means
The tire pressure monitoring system (TPMS) warns when a tire is underinflated or when a sensor or the system itself has a fault. A common cause is a tire that’s lost air; another possibility is a sensor issue after a tire change or rotation. If the light stays on after you correct pressure, a reset or service may be required.
Direct vs indirect TPMS
Direct TPMS uses actual sensors inside each tire to report pressures, while indirect TPMS relies on wheel-speed signals from the ABS system. Direct systems often provide a straightforward reset or relearn procedure, whereas indirect systems may require calibration after tire changes or pressure adjustments.
Reset options for Honda TPMS
There are two common reset paths on modern Honda vehicles: a button-based reset and an automatic relearn by driving. The exact steps depend on model year and trim, so treat these as general guidelines and refer to your owner’s manual for specifics.
Method 1: Button-based reset (typical on many Honda models)
Use this method if your model provides a dedicated TPMS reset or SET button and the instrument cluster interface supports TPMS calibration.
- Inflate all tires to the recommended cold pressure. Check the door placard on the driver's door jamb for the correct numbers.
- Turn the ignition to ON with the engine off (or to the RUN position on some vehicles).
- Locate the TPMS/SET button (common locations include under the dash to the left of the steering column or in the glove box). Press and hold the button until the TPMS indicator light blinks or a confirmation chime sounds, then release.
- Start the engine and drive at a steady speed (roughly 50 mph/80 km/h) for about 10 minutes to complete the relearn.
After the relearn completes, the TPMS light should go off. If it remains illuminated, recheck all pressures and consider repeating the procedure or seeking service.
Method 2: Automatic relearn by driving
Some Honda models complete the relearn automatically after the tires are inflated to spec. No manual button press is required in these cases.
- Check all tires and the spare (if equipped) to ensure they are inflated to the specified cold pressures on the placard.
- Drive normally on level roads at speeds above about 30 mph (50 km/h) for 10–20 minutes. If the light was a result of underinflation, it should reset once the relearn completes.
- If the light returns after a sufficient drive, recheck pressures and inspect tires for leaks or damage.
Note that some models might require a longer or shorter drive, or a specific sequence via the instrument cluster; always refer to your manual for exact instructions.
Method 3: Professional reset or sensor programming
If a sensor was replaced, a tire rotation occurred, or the light persists after attempts to reset, professional service is recommended. Some steps may require specialized equipment to program or relearn the TPMS sensors.
- Visit an authorized Honda dealer or a tire shop with TPMS programming capabilities to reprogram or relearn TPMS sensors for your vehicle’s year and model.
- Ask technicians to inspect sensors and valve stems for leaks or corrosion; damaged sensors may trigger ongoing warnings.
- Request a full system check if the light remains after a proper reset, as this can indicate a sensor fault or wiring issue.
Note: If your tires were recently replaced or rotated, the system may require a relearn for the new sensors; dealer or shop technicians can perform the procedure with a TPMS tool.
What to do if the light won’t reset
If the TPMS light remains on after inflating tires and attempting a reset, recheck pressures and inspect tires for punctures or leaks. A slow leak can cause the light to reappear after a short period. When in doubt, schedule service at a Honda dealer or a tire shop with TPMS capabilities.
Summary
Resetting the Honda TPMS typically involves correcting tire pressures to the recommended levels and using either a built-in TPMS reset button or a driving-based relearn. Because exact steps vary by model year and trim, consult the owner’s manual for precise instructions. If issues persist after a reset or if sensors were changed, professional service may be required to diagnose and reprogram TPMS sensors.