To reset the HR-V’s tire pressure monitoring, start by inflating all four tires to the recommended pressure shown on the door jamb sticker, then perform the TPMS calibration using the dedicated button (if equipped) or through the vehicle’s settings, and finally drive at highway speeds to complete the relearn. The exact steps can vary by model year and trim, so consult the owner’s manual if you’re unsure.
Understanding the process helps you avoid lingering tire-pressure warnings. Some HR-Vs use a physical TPMS reset button, while others rely on the instrument cluster’s menu to recalibrate. The goal is to ensure the system correctly recognizes each tire’s current pressure after adjustments, so the warning light can turn off once the tires are at the correct specification.
Reset procedures for HR-V models with a TPMS button
If your HR-V includes a dedicated TPMS button, use this sequence to recalibrate after adjusting tire pressures.
- Check all four tires and inflate them to the recommended PSI listed on the door jamb sticker. Do this when the tires are cold for an accurate reading.
- With the ignition in the ON position but the engine not running (or as specified in your manual), locate and press and hold the TPMS reset button.
- Hold the button until the TPMS indicator light blinks or flashes, then release it. This signals the system is entering calibration mode.
- Drive at a steady highway speed (about 50 mph / 80 km/h) for 10–15 minutes to complete the relearn process. The warning light should turn off once the relearn completes.
- If the light remains on after the drive, recheck tire pressures and repeat the process. If it still won’t reset, there may be a sensor issue.
The button location can vary by year and trim, often being near the steering column, under the dash, or inside the fuse/relay panel area. Refer to your owner’s manual for the exact location if you can’t find it.
Reset procedures via the instrument cluster / settings (indirect TPMS)
For HR-Vs without a TPMS button, calibration is usually done through the vehicle’s settings menu. This method is common on models that use indirect TPMS or rely on the onboard system to relearn after pressures are corrected.
- First, inflate all four tires to the recommended pressures on the door jamb sticker, ensuring the tires are cold before measuring.
- Turn the ignition to ON (engine OFF) and navigate to the TPMS calibration option in the instrument cluster or the vehicle settings menu. This is often found under Settings > Vehicle > TPMS Calibration or Tire Pressure Monitoring > Calibrate.
- Select Calibrate (or Relearn) and confirm. The system will begin the relearn process.
- Drive at a steady highway speed (around 50 mph / 80 km/h) for 10–15 minutes or as directed by the on-screen prompt to complete calibration. The TPMS light should extinguish when successful.
- If the warning persists after the drive, verify tire pressures again and retry the calibration. If issues continue, a sensor fault or vehicle software update may be needed.
Some newer HR-V models may place TPMS calibration under a slightly different path, such as Settings > Vehicle Information or a dedicated TPMS submenu. If you’re unsure, the owner’s manual or a dealer service department can provide model-specific instructions.
What to do if the TPMS won’t reset
If the TPMS warning remains after following the reset procedures, consider these possibilities and steps:
- Tires may not be at the exact recommended pressure, or temperatures are influencing readings. Recheck with a tire gauge when the tires are cold and retry.
- A sensor may be damaged or have a weak battery, especially after tire changes. A professional inspection may be needed.
- Wheel or tire sizes changed without reprogramming the TPMS. Ensure the system recognizes the current tires.
- There could be a software or firmware issue with the vehicle’s TPMS module. A dealer visit may be required for updates or diagnostics.
In cases where the light remains stubborn after multiple attempts, schedule a check with a Honda service center. They can diagnose sensor health, reset the system with OEM tools, and verify that there are no underlying tire or wheel issues.
Summary
Resetting the Honda HR-V’s tire pressure involves first ensuring all tires are inflated to the manufacturer’s recommended pressure, then performing a TPMS calibration via either a physical reset button (if equipped) or the vehicle’s settings menu, followed by driving at highway speed to complete the relearn. Since procedures vary by model year and trim, consult your owner’s manual or a dealer for the exact steps. A successful reset should illuminate the dashboard warning and confirm that the system correctly tracks current tire pressures.