You can replace the wiper blades on a 2020 Hyundai Palisade yourself in about 5 to 15 minutes by lifting the blades away from the windshield, releasing the old blades, and snapping on new ones sized for the Palisade (front driver 26 inches, front passenger 18 inches, rear 12 inches). Always verify blade lengths on your exact vehicle before purchasing.
For the 2020 Palisade, front blades handle the bulk of the work and use standard attachment points, while the rear blade is smaller and mounts differently on the tailgate. Blade lengths can vary by trim or regional market, and aftermarket blades may use different adapters, so confirm compatibility with your specific model and VIN before buying.
Tools and Materials
Before you start, gather the right blades and any adapters, plus a few simple supplies to help clean and finish the job.
- Front wiper blades: 26 inches (driver) and 18 inches (passenger)
- Rear wiper blade: about 12 inches
- Replacement adapter kit if your blades require a different connector than the stock arms
- Clean rag or tissue and a small amount of isopropyl alcohol for wiping the blade tips and arm junctions
With the right blades and adapters at hand, you’re ready to begin the swap.
Front Wiper Replacement
The front replacement follows a standard process used across many modern vehicles. The driver-side blade is longer (26 inches) than the passenger-side blade (18 inches), but the removal and installation steps are similar for both sides.
- Park the vehicle, turn off the ignition, and lift the driver-side wiper away from the windshield until it stands upright.
- Locate the blade’s release mechanism on the connector. For most blades, press the small tab or lever to release the blade from the wiper arm; some blades use a push-button or a small safety lock—follow the blade’s specific instructions.
- Detach the old blade from the arm and set it aside. Note whether you’re dealing with a J-hook, pin, or other connector so you choose the correct adapter for the new blade.
- Prepare the new blade by attaching the correct adapter to match your Palisade’s wiper arm if needed.
- Attach the new blade to the arm by aligning it and sliding it on until you hear or feel a click, then gently lower the wiper back onto the windshield.
- Repeat the steps for the passenger-side blade (18 inches).
- Test both front wipers to ensure smooth operation and complete clearance of the windshield. If streaking occurs, reseat or replace the blades as needed.
Front blades installed and tested. Confirm proper seating and compatibility with your chosen blades and adapters.
Rear Wiper Replacement
The Palisade’s rear wiper is smaller and mounts on the tailgate. Replacement typically involves a 12-inch blade and a straightforward clip-on or snap-on connection, though some models use a slightly different adaptor.
- Open or access the rear wiper by lifting the tailgate or locating the wiper on the rear glass, then lift the arm away from the glass to a comfortable working angle.
- Release the old blade from the arm. Depending on the design, you may need to press a small tab or rotate the blade to disengage it from the connector.
- Attach the new rear blade to the arm, ensuring it sits firmly in place with a click or secure lock.
- Lower the wiper arm back onto the rear glass and test the rear wiper to confirm full coverage and no streaking.
Rear blade replacement completed. Ensure the blade remains securely attached during operation to avoid detachment at high speeds or during rain.
Blade Sizes and Verification
Typical sizes for the 2020 Palisade
Common blade lengths for this model are:
- Front driver-side blade: 26 inches
- Front passenger-side blade: 18 inches
- Rear blade: 12 inches
Always verify exact lengths for your vehicle by checking the current blades, your owner’s manual, or Hyundai’s parts diagrams for your VIN. If you’re buying aftermarket blades, ensure the adapters match your wiper arm style.
Tips for a Smooth Replacement
To ensure a clean fit and longer blade life, wipe the wiper arm tips, remove any debris from the blade channels, and handle new blades with clean hands. When in doubt, bring an old blade to the store to match length and connector type exactly.
Summary
Replacing the 2020 Palisade wipers is a quick DIY task that restores visibility and safety during inclement weather. Front blades run about 26 inches on the driver side and 18 inches on the passenger side, with a 12-inch rear blade. Follow the step-by-step removal and installation process, verify adapter compatibility, and test the system after installation. Regular blade maintenance helps prevent streaks and chatter on the windshield.
How to change the wiper blades on a 2020 Palisade?
While pushing the lock pull down on the wiper. Blade then remove it from the arm. To place new blades on the arm. Fit the new blade on the arm. And pull it up into the fitting.
How to get windshield wipers up on palisade?
Stop right in the middle. And then by you doing that um you'll have full access to the wiper. And you'll be able to change it that way so that way you're not breaking the hood or anything like that.
What size wiper blades does a 2020 Hyundai Palisade take?
2020 Hyundai Palisade Wiper Blades Size/Price Chart
| Car | Driver | Pass. |
|---|---|---|
| 2020 Hyundai Palisade | 26 in. | 20 in. |
Can I remove wiper arms without a special tool?
I often remove wiper arms using a wrench, when I haven't got any locking pliers around.