Inflate all tires to the recommended pressures and reset the TPMS; if the light stays on, inspect for leaks or faulty sensors and have the system diagnosed by a professional.
Understanding why the TPMS light comes on
The tire pressure monitoring system illuminates when the vehicle detects one or more tires not at the correct pressure, or when there’s a calibration or sensor fault. On many 2010 Honda models, the system uses direct TPMS sensors in each wheel, which can be affected by punctures, slow leaks, sensor battery wear, or after tire service.
- Low tire pressure in one or more tires
- Puncture, slow leak, or damaged valve stem
- Faulty or dead TPMS sensor in a wheel
- Calibration or relearn issue after inflating tires or rotating tires
- Electrical or sensor receiver problems in the instrument cluster
The light may be solid if it’s a pressure issue or flash if the system detects a fault. If in doubt, treat it as a potential tire issue and inspect promptly.
First steps: check and correct tire pressures
Before attempting any reset, confirm all tires are inflated to the specified cold pressures listed on the door jamb placard or in the owner's manual. This helps determine whether the warning is truly caused by under-inflation or by a system fault.
- Check each tire’s pressure with a reliable gauge, including the spare if applicable to your model.
- Inflate every tire to the recommended cold pressure shown on the driver’s door placard or in the manual.
- Look for signs of punctures, nails, or slow leaks and inspect valve stems and rims for damage.
- After inflating to spec, drive for 10–15 minutes at highway speeds to allow the system to relearn the new pressures.
If the light goes out after proper inflation and a short drive, the issue is resolved. If it remains on, proceed to a reset or professional diagnosis.
How to reset the TPMS on a 2010 Honda
Resetting (relearning) the TPMS can help the system recalibrate after inflating the tires or after tire work. Procedures vary slightly by model, so use these general steps as a guide and consult the owner’s manual for your exact trim.
- With the ignition on (engine off), locate the TPMS reset button. It is often found under the dash, near the kick panel, or inside the glove box. If your model uses an on-screen menu, navigate to the TPMS calibration/relearn option.
- If using a hardware button: press and hold the TPMS button until the TPMS light on the dash blinks twice or a confirmation message appears.
- Drive at a steady speed, typically 30–50 mph (48–80 km/h), for about 10–20 minutes to complete the relearn. Do not perform aggressive driving during this period.
- If your model uses the instrument display instead of a physical button, follow the on-screen prompts to start the relearn, then drive as described above.
Some 2010 Honda models may not have a dedicated reset switch and instead require a dealer tool to perform a relearn. Always verify with the owner’s manual or a dealer if you’re unsure.
When the light won’t go away: potential sensor issues
If the TPMS light remains after inflating to the correct pressures and performing a relearn, you may be dealing with a faulty sensor, a weak battery in one sensor, or a problem with the system wiring or receiver. This typically requires diagnostic tools and sensor replacement by a tire shop or Honda dealer.
- Faulty or dead TPMS sensor in one wheel (common as sensors age)
- Leaky or damaged valve stem or tire bead causing repeated loss of air
- Malfunctioning TPMS receiver or instrument cluster fault
Costs vary by model and region, but sensor replacement typically ranges from roughly $50–$100 per sensor plus installation; a full system diagnosis can help pinpoint the exact issue.
Conclusion
To get rid of the TPMS light on a 2010 Honda, start with a thorough tire pressure check and correction, then perform a relearn if your model supports it. If the light persists, inspect for tire leaks and consider sensor health. When in doubt, a professional diagnostic can identify sensor or system faults and ensure safe, reliable operation.
Summary
Key steps: confirm proper tire pressures to spec, drive to relearn, and use the TPMS reset method appropriate to your model. If the warning persists, expect possible sensor or system faults and seek professional help to replace sensors or perform a diagnostic scan. Regular maintenance and timely tire repairs help prevent TPMS warnings in the future.