The engine takes about 4.5 quarts of oil with a new filter (roughly 4.3 liters).
The 2017 Ford Fusion 2.5 L uses a Duratec 2.5-liter four-cylinder. Oil capacity matters for routine maintenance, topping up, and ensuring the engine stays properly lubricated. This article provides the official capacity, typical oil types, and practical steps for changing the oil on this specific engine.
Oil capacity and specifications
The manufacturer lists an oil capacity of 4.5 quarts (4.3 L) when performing an oil change with a new filter. If you do not replace the filter, you may require slightly less oil, typically around 4.0–4.3 quarts, depending on how much is retained in the old filter. Always verify with the dipstick and the manual for your exact vehicle and market.
Note: Use the recommended viscosity per the owner's manual. For most US-market Fusions with the 2.5 L Duratec, that is 5W-20. Some climates or regions may specify 5W-30; always confirm in the owner’s manual or with Ford's service information.
Below is a quick reference to the oil-related details you’ll want before your change.
- Capacity with new filter: about 4.5 quarts (4.3 L)
- Capacity without changing the filter: roughly 4.0–4.3 quarts
- Recommended oil type: 5W-20 (check manual for your region)
Concluding: The typical oil volume for a complete change on the 2017 Fusion 2.5 L is around 4.5 quarts with a new filter. Use dipstick checks to fine-tune and avoid overfilling.
Oil change steps
If you’re changing the oil yourself, follow these general steps and ensure proper disposal of used oil and filter.
- Warm up the engine to operating temperature to ensure complete drainage.
- Turn off the engine, park on a level surface, and place a drain pan underneath the oil pan.
- Remove the drain plug and allow the old oil to drain completely.
- Remove and discard the old oil filter; install a new filter per the manufacturer’s instructions.
- Replace the drain plug and tighten to the specified torque.
- Fill with the recommended amount of oil (about 4.5 quarts with filter) and a little at a time.
- Start the engine, check for leaks, and recheck the oil level with the dipstick; top up if necessary to reach the correct level.
After the change, reset the oil life monitor if equipped and record the service for future reference.
Summary
For a 2017 Ford Fusion with a 2.5 L engine, plan on about 4.5 quarts of engine oil when performing a full change with a new filter, using the recommended 5W-20 viscosity unless your manual specifies otherwise. Always verify the exact capacity and spec for your vehicle variant and market, and use a reliable oil filter and filter torque. Regular checks and following the owner's manual will help maintain engine health.
What type of oil does a Ford Fusion 2017 take?
For modern Ford Fusion sedans, the manufacturer suggests SAE 5W-20 or SAE 5W-30 Motorcraft full synthetic oil for the gasoline engine. If you own a Ford Fusion hybrid, Ford recommends SAE 0W-20 oil that works for lower temperatures.
What's the typical lifespan of a fusion?
between 200,000 and 250,000 miles
The short answer is that a well-maintained Ford Fusion can last between 200,000 and 250,000 miles. Some Ford Fusion owners have even reported higher mileage with proper regular maintenance.
Do Ford Fusions shift hard?
It is a good idea to keep an eye and ear on the way your car sounds when you are accelerating, as the RPMs should never get so high that they are noticeable. Ford Fusion transmissions are also known for hard shifting issues.
How much oil goes in a 2017 Ford Fusion 2.5 L?
5.7 qt
Capacities and Specifications - 2.5L
| Item | Capacity |
|---|---|
| Engine oil (with oil filter). | 5.7 qt (5.4 L) |
| Engine coolant. | 7.2 qt (6.8 L) |
| Brake fluid. | Between MIN/MAX on brake fluid reservoir |
| Automatic transmission fluid.* | 9.0 qt (8.5 L) |