The 2017 Chevrolet Impala with the 3.6-liter V6 generally requires about 6 quarts of engine oil for an oil change, with roughly 5.7 quarts needed after installing a new filter.
The exact amount can vary slightly depending on the engine build, the specific oil filter used, and whether the filter is replaced during service. For the most precise figure, consult the owner's manual or GM service data for your vehicle’s exact configuration.
Capacity and how it is measured
Capacity figures at a glance
GM’s official data for the 3.6L V6 used in the Impala lists a total oil capacity of about 6 quarts (5.7 liters), and a fill amount of around 5.7 quarts (5.4 liters) when installing a new filter. In practice, technicians commonly fill to the 5.7-quart mark and top up as needed after starting the engine.
- 5.7 quarts (5.4 liters) with a new oil filter
- 6 quarts (5.7 liters) total system capacity
When performing an oil change, it’s typical to have a 6-quart container on hand to ensure you can reach the correct level after replacing the filter. After draining, check the dipstick and add oil gradually until the level sits within the recommended range.
Oil specification and viscosity
Recommended oil standards
The Impala’s 3.6L V6 generally calls for Dexos1 Gen 2 synthetic oil with a viscosity of 5W-30. This specification helps provide reliable protection and optimal performance across a wide range of driving conditions. Always verify the exact requirement in your owner’s manual or GM service data for your car’s year and configuration.
- Dexos1 Gen 2 synthetic oil, 5W-30 is typically recommended
- Check the manual for climate-specific notes or alternative viscosities if applicable
Using an approved oil and maintaining the correct viscosity supports engine longevity and warranty terms where applicable.
How to change the oil
Procedure overview
If you’re performing an oil change yourself, follow these general steps. The following list outlines the typical process for a 3.6L V6 Impala change. Always consult the service manual for torque specs and any model-specific instructions.
- Warm the engine briefly, then park on a level surface and gather tools (new filter, the recommended oil amount, drain pan, wrench, funnel).
- Place the drain pan beneath the oil pan and remove the drain plug to let old oil drain completely.
- Remove the old oil filter, install the new filter with a light coating of fresh oil on the gasket, and ensure it’s snug but not over-tightened.
- Reinstall the drain plug with the proper torque, then pour in about 5.7 quarts (5.4 liters) of the required oil.
- Start the engine, let it run briefly to circulate the oil, check for leaks, and then turn off.
- Check the oil level with the dipstick and add small amounts of oil as needed to reach the correct mark. Reset the oil-life monitor if applicable.
Following these steps helps ensure proper lubrication and accurate oil level. If you’re unsure about any step, a professional technician can perform the change to GM specifications.
Summary
For a 2017 Chevy Impala with a 3.6L V6, the typical oil-change fill is about 6 quarts in total, with roughly 5.7 quarts required after replacing the filter. The recommended oil is Dexos1 Gen 2 synthetic at 5W-30, though you should confirm the exact specification in your owner’s manual. Always verify the level with the dipstick after completing the change and consult the manual for any model-specific instructions.
How many quarts of oil does a 2017 Chevy Impala 3.6 take?
6 quarts (with filter). After refill check oil level.
How much oil does a 3.6 V6 Chevy engine take?
6.0 quarts
3.6L V6 Engine—6.0 quarts (with filter)
What oil brand does Chevy recommend?
The top Chevy Silverado 1500 oil is ACDelco dexos1 SAE 0W-20 full synthetic motor oil for the 5.3L and 6.2L gasoline engines. For the smaller 2.7L TurboMax high-output engine, you'll need ACDelco dexos1 SAE 5W-30 full synthetic oil.
How much oil does a 2017 Chevy 3.6 take?
6 quarts
Engine Oil
Capacity: 6 quarts (with filter).