The 2014 Ford Taurus with the 3.5 L V6 typically requires about 6.0 quarts of engine oil when you replace the filter (roughly 5.7 liters).
Oil capacity can vary slightly depending on whether you’re changing the filter, the exact engine variant, and regional specifications. Always verify with the owner’s manual or the under-hood label and confirm the level with the dipstick after a change.
Understanding the figures
Below are the standard capacity figures you’re most likely to encounter for the 2014 Taurus with a 3.5 L V6. These numbers reflect the amount needed for a complete oil change that includes replacing the oil filter. They can differ if you’re topping up or if a different filter is used.
Before the list, note that these values assume a full oil change with a new filter and may vary slightly in production batches or with aftermarket filters.
- With oil filter: 6.0 quarts (5.7 liters)
- Without oil filter: about 5.0 quarts (4.7 liters)
In practice, after adding oil, start the engine and check for leaks, then use the dipstick to bring the level to the full mark. If you’re close to the minimum, add a little at a time and recheck.
Oil type and change considerations
For the 3.5 L Ti-VCT V6 in the 2014 Taurus, Ford commonly recommends 5W-20 motor oil and notes that either a synthetic blend or full synthetic oil can be used depending on climate and driving conditions. If you live in extreme temperatures or plan aggressive driving, you may opt for higher-quality synthetic options, but always follow the manufacturer’s guidance and warranty requirements.
Practical guidance for oil changes
When planning an oil change, consider the following:
- Use the correct filter and a fresh gasket seal if applicable.
- Dispose of used oil at an authorized recycling facility.
- Reset the oil life monitor after completing the change (if equipped).
Consult the owner’s manual or a dealer service department if you’re unsure about the exact specification for your vehicle’s trim or regional variation.
Summary
For the 2014 Ford Taurus with a 3.5 L V6, plan for about 6.0 quarts (5.7 liters) of oil when performing a full change with a new filter, or roughly 5.0 quarts (4.7 liters) if you’re changing oil without replacing the filter. Always verify with the official manual and use the dipstick to ensure the oil is at the correct level after servicing.
How fast can a Taurus run?
Back in 2020 nobody would have expected a Ford Taurus to run a 1/4 mile in the 8 seconds. Let alone at over 170mph! This 2020 combination was so simple and thats the insane part. A Yamaha SHO engine, 11:1 compression forged rods and pistons and about 32psi of boost from a 72mm Precision turbo.
What engine do police Taurus have?
| Ford Taurus (sixth generation) | |
|---|---|
| Powertrain | |
| Engine | 2.0 L EcoBoost I4-T 240 hp (2013–2017) 3.5 L Cyclone V6 263 hp (2010–2012) 3.5 L Cyclone V6 288 hp (2013–2019) 3.5 L EcoBoost V6 365 hp (2010–2019) 3.7 L Cyclone Ti-VCT FFV V6 305 hp (Police Interceptor Sedan, all-wheel drive only) (2013–2019) |
How many quarts of oil does a 2014 Ford Taurus 3.5 L take?
6.0 quarts
How much oil does a 2014 Ford Taurus need? Approximate capacity: the 3.5L V6 typically requires about 6.0 quarts with a filter change; exact capacity is confirmed during service.
How much oil does a 3.5 L V6 Ford Taurus take?
about 6 quarts
The 3.5L V6 typically requires about 6 quarts of oil.