It takes about six quarts (roughly 5.7 liters) of engine oil for a full oil change on the 2013 Chevrolet 3.6L V6, including a new filter.
The 3.6-liter V6 used in several 2013 Chevrolet models (including the Camaro, Malibu, Impala, and Traverse) shares this overall oil capacity across its LLT/LFX variants. Exact requirements can vary slightly based on whether you replace the filter and the specific engine variant, so always confirm with your owner's manual or a trusted service guide for your vehicle.
Oil capacity and specifications
The following details summarize the typical capacity and the recommended oil type for the 3.6L V6 engines found in 2013 Chevy models.
- Oil capacity: 6 quarts (5.7 liters) with a new filter during a full change.
- Recommended oil type: Dexos1 Gen 2 certified 5W-30 (check owner's manual for exact specification and climate considerations).
- Notes: This capacity applies across the common 3.6L variants used in 2013 Chevrolet models; if you do not replace the filter, the amount needed may be slightly less.
When performing an oil change, use the full 6-quart capacity to ensure the system reaches the correct level with a new filter, then verify the level with the dipstick after a short idle and recheck after a few minutes of running.
Vehicles in 2013 powered by the 3.6L V6
Several Chevrolet models in the 2013 lineup used the 3.6L V6, and the oil capacity remains consistent across these applications. Verify model-specific requirements in the manual if you’re unsure which engine your car uses.
- Chevrolet Camaro (3.6L V6, LLT/LFX variants)
- Chevrolet Malibu (3.6L V6)
- Chevrolet Impala (3.6L V6)
- Chevrolet Traverse (3.6L V6)
For any model not listed here or for a particular build, consult the owner's manual or a dealership to confirm the exact oil capacity and specification.
How to change the oil (step-by-step guide)
Below is a general, here-and-now guide for performing an oil change on a 2013 Chevy with a 3.6L V6. Always follow safe practices and refer to the service manual for torque specs and procedures.
- Prepare: Gather the proper Dexos1 Gen 2 5W-30 oil, a new oil filter, a drain pan, a socket wrench, funnel, and jack stands or ramps.
- Warm up: Run the engine briefly to loosen oil, then turn it off and safely lift the vehicle if needed.
- Drain old oil: Place the drain pan under the oil pan, remove the drain plug, and allow the oil to drain completely.
- Replace filter: Remove the old oil filter, install the new filter (wipe the gasket and apply a light coat of oil), and hand-tighten.
- Reinstall drain plug: Torque to the manufacturer's specification, typically around 15–22 ft-lbs depending on the engine.
- Add new oil: Pour in 6 quarts (5.7 liters) of the recommended oil, then run the engine briefly to circulate.
- Check level: With the engine off, wait a minute, then check the dipstick and adjust the level to the full mark if needed.
- Final checks: Look for leaks around the filter and drain plug, and properly dispose of the old oil and filter.
Keep in mind that torque specs, oil type, and capacities can vary slightly by model and year. Always verify with your manual or a trusted service resource before proceeding.
Summary
The 2013 Chevrolet 3.6L V6 typically requires 6 quarts (5.7 liters) of engine oil with a new filter for a complete change, using Dexos1 Gen 2 5W-30 oil. This capacity applies across the common LLT/LFX variants used in models like the Camaro, Malibu, Impala, and Traverse. Always confirm exact specifications for your vehicle and follow proper oil-change procedures to ensure optimal engine health.