On a 2010 Honda Accord, replacing a front wheel bearing (hub assembly) typically costs about $400–$600, with $700–$800 possible in high-cost regions or when OEM parts and additional services are involved. Rear bearing replacement generally falls in a similar range, though precise prices vary by shop and location.
The final price depends on several factors: whether you’re replacing the front or rear bearing, whether you install aftermarket or OEM parts, local labor rates, and whether extra work is needed such as CV axle replacement, brake service, or ABS sensor work. The following sections break down the costs and the factors that influence them.
Cost basics for a 2010 Honda Accord
Wheel bearings for the Accord are typically replaced as part of a hub assembly. Labor mainly covers removing the wheel, braking components, and securing the hub in place. In some cases, the CV axle or other related components may need attention, which can raise the total price. Below are typical ranges you can expect when shopping for front versus rear bearings.
Below are common scenarios and ballpark totals to guide expectations.
What you pay for (front vs rear)
Costs below reflect typical scenarios for the 2010 Honda Accord in the United States as of 2024–2025. They include both parts and labor and assume standard wear without significant damage to the axle or surrounding components.
- Front hub/ bearing replacement with aftermarket parts: roughly $250–$450 total
- Front hub/ bearing replacement with OEM dealer parts: roughly $450–$750 total
- Rear hub/ bearing replacement with aftermarket parts: roughly $200–$350 total
- Rear hub/ bearing replacement with OEM dealer parts: roughly $350–$550 total
- Additional work (CV axle replacement, brake service, ABS sensor, etc.) during the same visit: add about $150–$600
Note: These ranges are typical estimates. Exact prices depend on your location, the shop, and the specific part choices. Always request a written estimate that itemizes parts and labor before authorizing work.
What drives the price
The following factors most influence the final bill for wheel bearing replacement on a 2010 Honda Accord.
Front vs rear bearing
Front bearings are usually more expensive to replace than rear bearings because the front hub assembly includes more components and is often the more labor-intensive job on a unibody front-wheel-drive car.
Parts quality: aftermarket vs OEM
Aftermarket hub assemblies are typically cheaper than OEM (dealer) parts. OEM parts may offer longer warranty coverage and tighter fit but cost more upfront.
Labor rates and region
Labor costs vary widely by region and shop. urban areas or dealerships tend to charge more per hour than rural independent shops.
Additional repairs on the same axle
If the CV axle is damaged or the brakes/ABS sensor require service, those costs add to the total. Sometimes the axle must be replaced along with the hub, which significantly increases price.
Vehicle condition and rust/fitment issues
Rusty fasteners or corroded hub assemblies can prolong the job, increasing labor time and cost.
Typical ranges by scenario
These ranges provide a quick reference for budgeting. They assume standard, non-emergency service at a typical shop. Always verify a current quote for your exact vehicle and location.
- Front hub bearing replacement with aftermarket parts: $250–$450
- Front hub bearing replacement with OEM parts: $450–$750
- Rear hub bearing replacement with aftermarket parts: $200–$350
- Rear hub bearing replacement with OEM parts: $350–$550
- Additional work (CV axle, brakes, ABS sensor) bundled in: +$150–$600
Note: Prices can exceed these ranges in markets with higher labor rates or when additional issues are found that require more extensive repairs. Always get a written, itemized estimate before approving work.
Regional variations and how to save
Prices vary by country, currency, and shop policy. In the United States, large metropolitan areas and independent shops may beat dealership quotes, especially when aftermarket parts are acceptable. Getting multiple estimates and asking for a breakdown of parts versus labor can help you compare value. Some shops offer free inspections and diagnostic checks, which can help you determine whether the bearing is the root cause or if more extensive axle or CV joint work is needed.
Summary
For a 2010 Honda Accord, plan on roughly $400–$600 for a front wheel bearing/hub replacement with aftermarket parts, and $450–$750 if you opt for OEM parts. Rear bearing work generally falls in a similar range, though it can be a bit cheaper. The final price hinges on parts choice, labor rates, and whether extra repairs are required on the same axle. To avoid surprises, obtain several written estimates, ask for a clear breakdown of parts and labor, and confirm whether any adjacent components (CV axle, brakes, ABS sensor) will be addressed in the same visit.