Typically, you can expect to spend about $300 to $600 per axle for a wheel bearing (hub assembly) replacement on a Honda Accord, including parts and labor. Dealers using OEM parts usually charge more, while independent shops using aftermarket parts can be cheaper. Actual prices vary by model year, region, and whether additional services are needed.
Understanding the cost requires looking at what goes into the job. Modern Hondas tend to use hub assemblies that include the wheel bearing and sometimes the ABS sensor. The price you see will depend on the part choice (aftermarket vs OEM), the labor rate in your area, and whether any extras like an alignment or sensor replacement are needed after the swap.
What goes into the price
Before breaking down typical price ranges, it helps to know the main components that make up the cost:
- Parts: hub assembly (bearing included) or a bearing kit, with aftermarket parts usually cheaper than OEM Honda parts.
- Labor: time to remove the old hub, press in or bolt in the new hub, and test drive; labor rates vary by shop and region.
- Extras: ABS sensor replacement (if faulty), wheel alignment, new lug nuts, or brake inspection after the job.
In practice, the total per axle typically falls within a broad range, but you should consider all the factors above when budgeting for the repair.
Typical price ranges for a Honda Accord
Below is a general guide to what you might pay, including parts and labor, per axle. Use this to set expectations before you shop around.
- Aftermarket hub assembly replacement (most common at independent shops): roughly $250 to $500 per axle.
- OEM Honda hub assembly replacement (dealer or shop using OEM parts): roughly $400 to $900 per axle.
- Bearings-only replacement (less common on newer Accords; parts cost varies): roughly $150 to $350 for parts, with similar labor time to a full hub swap.
Note: These ranges assume a standard tire and wheel setup and typical labor rates. Taxes, shop fees, and regional price differences can shift the total higher or lower.
Cost by part type and service level
Different service levels and part configurations produce different total costs. The following breakdown helps illustrate how your choice affects the bottom line.
- Hub assembly replacement (recommended route for most modern Accords): total typically $300–$700 per axle when using aftermarket parts, and $500–$1,000+ per axle for OEM parts at a dealership.
- Bearing-only replacement (if available and feasible on an older generation): total typically $180–$450 per axle, depending on part source and shop labor.
When shopping, request itemized quotes that separate parts and labor so you can compare apples-to-apples and understand where any premium is coming from.
Geography, model year, and part availability
Prices fluctuate based on where you live and the Accord generation you own. Hardware and labor can be more expensive in urban areas or near dealership networks, while rural or discount shops may offer lower quotes. Also, earlier generations (outside modern hub assemblies) may require different repair approaches, which can influence both cost and turnaround time.
Model-year trends to know
- Pre-2010 Accords often used hub assemblies with bearings that could be replaced as a unit, but some older models allowed bearing-only service.
- 2010s to present Hondas typically use hub assemblies that include the bearing and may incorporate ABS sensor components, which can add to parts cost but streamline labor since the unit is replaced as a single piece.
Tips to save money and get the right repair
To minimize costs while ensuring a safe repair, consider the following:
- Obtain multiple, itemized quotes from independent shops and dealerships to compare parts and labor.
- Ask whether the quote includes a wheel alignment and ABS sensor inspection; some shops discount bundled services.
- Consider aftermarket hub assemblies if you don’t require OEM parts and you’re comfortable with non-OEM options that carry warranties.
- Check for promotions or coupons from local shops; the price can vary by region and time of year.
Always verify that any quoted price includes the necessary tests, such as a road test and a check for ABS functionality, and ask about warranty coverage on parts and labor.
Summary
Replacing a wheel bearing (hub assembly) on a Honda Accord usually costs around $300–$600 per axle, with dealer OEM parts pushing toward the higher end and aftermarket parts through independent shops typically closer to the lower end. Prices depend on the model year, the inclusion of ABS sensors, labor rates, and whether an alignment or other services are required. To get the best value, compare multiple quotes, confirm what’s included, and consider aftermarket options if you’re comfortable with them.