The engine oil capacity for the 2018 Murano’s 3.5 L V6 is 5.8 quarts when performing a full oil change with a new filter, and about 5.5 quarts if the filter is not replaced. The vehicle typically uses 0W-20 synthetic oil, though you should confirm the exact specification in your owner's manual for your region.
In this article, we break down the official capacity figures, explain how they are applied in practice during an oil change, and offer practical tips for checking and topping up the oil to the correct level. We focus on the 2018 Murano with the 3.5 L V6 engine, while noting that regional differences and maintenance history can influence the exact amounts. Always consult your owner’s manual or a Nissan dealer for the precise specification for your vehicle.
Oil capacity for the 2018 Murano 3.5L
Below is a concise summary of the engine oil capacity figures you should know when servicing a 2018 Murano with the 3.5 L V6.
Capacities by filter status
- Engine oil capacity with the filter installed: 5.8 quarts
- Engine oil capacity without replacing the filter: 5.5 quarts
Note: These figures represent typical values for a complete oil change. Real-world numbers can vary slightly based on engine condition, the exact oil filter used, and regional service specifications. Always verify with the dipstick after filling to ensure the level is at the full line.
Oil grade and maintenance notes
For the 3.5 L V6 in most markets, Nissan commonly recommends synthetic 0W-20 oil as the standard grade. Use a high-quality oil and a compatible filter for best results. If you are in a region with different climate or local requirements, refer to the owner’s manual or consult a Nissan service professional to confirm the correct viscosity and capacity.
- Confirm the recommended oil viscosity for your region (often 0W-20) in the owner's manual.
- Install a new, compatible oil filter during the change.
- Pour approximately 5.8 quarts of oil to reach the full level with the filter installed, then run the engine for a minute to circulate.
- Shut off the engine, wait several minutes, and recheck the dipstick; top off carefully if the level is below the full line.
Tip: If you only need to top up, use the dipstick as your guide to avoid overfilling, which can impact engine performance and emissions.
Summary
For the 2018 Nissan Murano with the 3.5 L V6, plan on about 5.8 quarts of engine oil for a full change with a new filter (roughly 5.5 quarts if the filter isn’t replaced). Use 0W-20 synthetic oil in most regions, and always verify exact specifications in the owner’s manual or with a Nissan dealer. Regularly checking the oil level with the dipstick helps ensure you stay within the correct range between changes.
How much oil does a 3.5 V6 engine take on a Nissan Murano?
~5.1 quarts
Murano Oil Capacity
Here's how much oil your Murano needs: 2015–Present Murano (3.5L V6): ~5.1 quarts with filter. 2009–2014 Murano (3.5L V6): ~5.1 quarts with filter. 2003–2007 Murano (3.5L V6): ~4.4–4.5 quarts with filter.
How much oil does a 2018 Nissan Murano 3.5 L take?
5.1 quarts
Oil Grade: API*
| Viscosity: | 0W-20 (All TEMPS) |
|---|---|
| Capacity: | 5.1 quarts (with filter). After refill check oil level. |
| Torque: | 25 ft/lbs (Oil Drain Plug) Install a new washer on the drain bolt. Only use an OE drain plug. |
How much oil does a 2018 Nissan 3.5 take?
5.1 quarts
Engine Oil. Capacity: 5.1 quarts (with filter). After refill check oil level.
What kind of oil does a Nissan Murano 3.5 take?
SAE 0W-20 full synthetic motor
2015–2024 Nissan Murano oil type (third generation, 3.5L V6)
For these third-generation models, Nissan updated the recommended oil type compared to older Muranos. Typical specification for 2015–2024 Murano models: Preferred oil type: SAE 0W-20 full synthetic motor oil.