How do you reset the tire pressure light on a Honda Civic?

To reset the tire pressure light on most Honda Civics, inflate all tires to the recommended cold tire pressures, then perform the TPMS relearn using either a dedicated reset button or the vehicle’s settings menu, and drive a short distance to complete the relearn.

The tire pressure monitoring system (TPMS) detects pressure changes in the tires and triggers the warning light when a tire is underinflated or when sensors are replaced. The exact reset steps vary by model year and trim. This guide outlines reliable methods common across many Civics and highlights year-specific differences.

Two reliable reset methods

Most Civics can be reset using either a hardware button or the on-screen/settings menu. The method you use depends on your model year and trim. Inflate tires first to the recommended figures on the door placard.

Method A — Physical TPMS reset button (where available)

If your Civic has a dedicated TPMS button, follow these steps in the order shown. Note that some models require you to be in a specific mode or to hold the button for several seconds.

1. Ensure all tires are cold and inflated to the recommended pressures shown on the door placard or in the owner’s manual.


2. Turn the ignition to ON (engine off) or start with the engine running, depending on the model.


3. Locate the TPMS reset button, usually near the lower-left dash area, under the steering wheel, or near the hood release.


4. Press and hold the TPMS button until the warning light blinks or a confirmation chime is heard, then release.


5. Drive the car at normal speeds for about 10 minutes (or until the light stops flashing) to complete the relearn.

Note: If your Civic does not have a physical TPMS button, skip to Method B. If the light remains after relearn, check for tire leaks or sensor faults and seek service.

Method B — TPMS Learn/Reset via the vehicle’s settings menu

Many recent Civics use the instrument cluster or infotainment system to relearn the TPMS. Use the display to locate the TPMS reset or learn option.

1. Confirm all tires are inflated to the recommended cold pressures. Recheck with a reliable gauge.


2. Turn the ignition to ON, with the engine off, or start the engine as recommended by your model.


3. Access the vehicle settings: in the instrument cluster or infotainment display, navigate to Settings > Vehicle (or Vehicle Settings) > TPMS (or Tire Pressure Monitor) > Learn (or Reset).


4. Select Reset or Learn and acknowledge any prompts.


5. Drive for about 10 minutes at speeds over 30 mph to complete the relearn, after which the light should go out.

Tip: On some Civics, the Learn option may be labeled as "Relearn" or "Reset" and could appear only after the car detects a recent tire pressure change or is in a specific mode (e.g., Vehicle Settings). If you don’t see the option, consult the owner’s manual for your exact year and trim, as the procedure can differ.

What to do if the light stays on or reappears

If the TPMS light remains on after inflating to the correct pressures and performing a relearn, or if it comes back after a short drive, there may be a slow leak, a damaged sensor, or a dead sensor battery. Common causes include:

• Underinflated tire that is punctured or leaks slowly


• TPMS sensor fault due to age or damage


• Recent tire rotation that didn’t trigger a relearn

In these cases, have the tires inspected by a technician who can check for leaks, sensor faults, or a need for tire replacement, and perform a professional TPMS reset if needed.

Notes for different model years

The exact path and buttons can vary between Civics from different generations. As a rule of thumb:

• Newer Civics (around 2016 and later) often support TPMS reset via Settings > Vehicle > TPMS > Learn.


• Older Civics may rely on a physical TPMS reset button or simple drive-to-relearn behavior after inflating to recommended pressures.

Always consult the owner’s manual for precise instructions tailored to your exact year and trim, as the procedure can differ even within a generation.

Summary

Resetting the tire pressure light on a Honda Civic involves first bringing all tires to the recommended cold pressures, then performing a TPMS relearn using either a physical reset button (if equipped) or the vehicle’s settings menu. A brief highway drive usually completes the relearn. If the light persists, there may be a leak or sensor issue that warrants professional service. Regularly checking tire pressures helps prevent nuisance warnings and maintains safety and efficiency.