Inflate all tires to the recommended cold pressures and use the TPMS reset method for your trim (or drive at highway speed to trigger an automatic relearn). If you’re unsure, check the owner’s manual for your exact model configuration.
The tire pressure monitoring system (TPMS) in a 2013 Honda Accord warns you when tire pressures fall below the specified levels. Resetting the light involves ensuring correct pressures first, then initiating a recalibration either with a dedicated reset button (if your trim has one) or by driving to trigger an automatic relearn. Exact steps can vary by trim and equipment, so consult the manual if you’re uncertain. Below are the common approaches and troubleshooting tips.
What you need to know before resetting
Before attempting a reset, verify that all four tires (and the spare, if your system monitors it) are inflated to the recommended pressures and that there are no visible leaks or damaged tires. A reset won’t work if a tire is still underinflated or damaged.
- Check tire pressures against the door jamb placard or the owner's manual for the exact cold-pressure specification.
- Inspect tires for cuts, punctures, bulges, or slow leaks and repair or replace as needed.
- Ensure tires are cold before measuring; pressure can rise with driving.
With properly inflated tires and no obvious issues, proceed to the reset procedure that matches your car’s configuration.
Reset procedures for a 2013 Honda Accord
There are two common methods depending on whether your Accord has a TPMS reset button or relies on automatic relearn. The steps can vary by trim, so refer to your owner’s manual if needed.
Option A: Reset button (if equipped)
Some 2013 Accords include a TPMS reset or calibration button located under the left side of the dash near the steering column or inside the fuse panel. The goal is to trigger recalibration after the tires are properly inflated.
- With the ignition in ON and the engine off, locate the TPMS/SET button.
- Press and hold the button for several seconds until the TPMS indicator light begins to flash or blinks and then goes out.
- Release the button. The system should enter calibration mode.
- Drive at highway speeds (around 50–60 mph / 80–100 km/h) for about 10 minutes to complete the relearn.
After this list, the recalibration should be complete and the light should stay off if successful. If it returns, retry the steps or proceed to troubleshooting.
Option B: Automatic relearn (no reset button)
If your model lacks a reset button, or you prefer automatic relearning, follow the steps below. This method relies on the system learning the correct pressures as you drive.
- Inflate all tires to the recommended cold pressures and double-check with the placard on the driver’s door or in the manual.
- Start driving and maintain speeds above 50 mph (80 km/h) for about 10 minutes to allow the TPMS to relearn the new pressures.
- If the light goes out, you’re done. If it remains on, try turning the ignition off and back on and drive again; if it still stays on, there may be a sensor fault or other issue requiring professional inspection.
If the light persists after a full relearn attempt, consider scheduling service to check TPMS sensors, the battery in each sensor, or related electronics.
What to do if the light stays on or reappears
A persistent TPMS warning can indicate a slow leak, a failed sensor, or a weak sensor battery. Take these steps:
- Re-check tire pressures after driving a short distance; if a tire continues to lose air, repair or replace it as needed.
- Inspect each TPMS sensor and valve stem for damage or corrosion; consider professional testing if leaks are suspected.
- Have the system diagnosed by a tire shop or Honda technician if the light remains after a full relearn.
Note: Some 2013 Honda Accord configurations require professional TPMS programming or sensor replacement, especially if sensor batteries have aged or a wheel sensor has failed.
Summary
Resetting the tire pressure light on a 2013 Honda Accord generally involves inflating all tires to the correct cold pressures and then either using a TPMS reset button (if your trim has one) or performing a highway-speed relearn by driving. If the light persists, check for leaks, inspect sensors, and seek professional help to diagnose sensor or module issues. Regular tire maintenance helps keep TPMS accuracy and reduces nuisance warnings.