Typically the TPMS reset button sits on the lower left dash near the driver's knee, often behind a small cover or adjacent to the fuse panel. If your model relies on the instrument cluster, you reset TPMS from the vehicle’s settings instead of a physical button.
The exact location varies by year and trim. This guide explains common placements for recent Accords, how to reset TPMS with a button or via the settings menu, and what to do if the warning light won’t reset. It covers both older and newer models to help you identify the correct procedure for your car.
Common TPMS button locations by model year
Because Honda has changed the interface over generations, the TPMS reset control may be a physical button or a menu option. Use the list below to check likely spots on your Accord:
- 2013–2017: Look for a small TPMS/RESET button on the left side of the dash, near the knee area or next to the hood release lever. It may be tucked behind an access panel.
- 2018–2024: Some trims omit a dedicated button. TPMS reset is often done through the Driver Information Display or center touchscreen: Settings > Vehicle > TPMS > Reset (or a similar path). The reset control on screen may be labeled TPMS or Reset.
- If you can’t locate a button: Check behind a small cover on the lower dash, under the steering column cover, or consult your owner’s manual for the exact location for your specific trim and year.
In short, older Accords tend to have a physical TPMS button, while many newer models rely on a software-based reset in the vehicle’s settings. If you’re still unsure, your dealer or a repair shop can confirm the correct spot for your VIN and trim.
Resetting TPMS: step-by-step options
Choose the method that matches your car’s configuration. Below are the two main paths: with a dedicated button and via the vehicle’s settings.
- Check all tires and inflate to the recommended pressures (found on the driver-side door placard or in the owner’s manual).
- Turn the ignition to ON with the engine off.
- If you have a physical TPMS/RESET button: press and hold it for about 3–5 seconds until the TPMS indicator light blinks or you hear a short beep, then release.
- Drive straight for roughly 10 minutes at speeds above 30–40 mph to complete the relearn process. The light should go out when the system finishes relearning.
- If the light remains after the drive, recheck pressures and inspect tires for leaks or damage; consider a dealer visit if the light stays on.
Note: Some trims require you to complete the relearn while the engine is running or to perform a second reset if the initial attempt doesn’t succeed. Always refer to your owner’s manual for model-specific instructions.
Using the settings menu to reset TPMS
On models without a dedicated TPMS button, the reset is typically done through the vehicle’s display interface. Use these steps as a general guide:
- Ignition ON, engine off; access the Driver Information Display or central touchscreen.
- Navigate to Settings > Vehicle > TPMS > Reset (or Calibrate).
- Confirm the reset, then drive to complete the relearn.
After performing the on-screen reset, continue to drive as directed to allow the system to relearn sensor data. If the option isn’t visible, your trim may require a dealership diagnostic tool to complete the reset.
What to do if the TPMS warning stays on
If the warning light remains lit after a reset, take these steps to diagnose common causes:
- Check all tire pressures again to confirm they are at the recommended levels.
- Inspect tires for nails, punctures, or slow leaks; address any leaks with a repair or replacement as needed.
- Examine valve stems for damage or corrosion and ensure sensors aren’t physically damaged.
- A faulty TPMS sensor or battery can trigger a persistent warning; a professional diagnostic using a TPMS scan tool may be required to identify the faulty wheel and reprogram or replace sensors.
Persistent warnings beyond normal pressure checks typically require service. The dealership or a qualified tire shop can perform a precise sensor diagnosis and TPMS programming.
Additional considerations and tips
Keep these ideas in mind to maintain TPMS accuracy and minimize reprogramming needs:
- Always inflate tires to the recommended pressure, including the spare if your vehicle’s TPMS monitors it.
- When rotating or replacing tires, you may need to reset or recalibrate the TPMS for new sensor positions.
- Sensor batteries have a limited lifespan; a failing sensor may trigger a warning even if pressures are correct.
If you frequently reset TPMS or notice frequent pressure changes, have your tires and sensors inspected to prevent false readings and ensure safe driving conditions.
Summary
On many Honda Accords, the TPMS reset control is a physical button on the lower left dash in older models, while newer trims often rely on the Settings menu in the center display. To reset TPMS, inflate all tires to the recommended pressures, then follow the button-press or on-screen steps and drive to complete the relearn. If the warning light persists, recheck pressures and inspect tires, or seek professional service for sensor diagnostics and replacement if needed.