For a 2009 Honda Fit, you need the engine oil filter that fits the 1.5-liter i-VTEC engine (L15A1). In most production runs the OEM part is 15400-PLM-A02, with some early or late 2009 builds using 15400-PLM-A01. Always verify with your VIN or by checking the filter on the car.
The following guidance covers how to identify the exact filter for your specific car, what options exist (OEM vs aftermarket), and how to replace it during an oil change.
Identify the correct filter for your engine
OEM Honda options
The Honda factory filter for the 1.5L Fit has been cataloged under a couple of common part numbers. Start here if you want exact compatibility from Honda's own parts catalog:
- 15400-PLM-A02 (common for many 2009 Fits with the 1.5L engine)
- 15400-PLM-A01 (used on some 2009 production runs)
Note: Exact part number can vary by production date and country. When in doubt, verify via VIN or compare with the filter you remove during an oil change.
Aftermarket options
Many major filter brands offer replacements that fit the 1.5L Fit. Use these guidelines to choose:
- Look for filters labeled as compatible with Honda Fit 1.5L or L15A engines.
- Check the retailer's cross-reference to ensure the filter will fit your 2009 model year.
If a filter doesn't clearly list fit for the 1.5L Fit, avoid it or confirm with the seller before purchasing.
Replacing the oil filter and oil
Follow this practical sequence when performing an oil change and filter replacement. This helps ensure a proper seal and clean operation for the engine.
- Warm up the engine, then park on a level surface and engage parking brake.
- Place a drain pan under the oil pan and remove the drain plug to drain the used oil.
- Loosen and remove the old oil filter with an oil filter wrench. Expect some oil to spill.
- Coat the new filter's gasket with a light film of new engine oil, then thread it by hand until snug and tighten an additional 3/4 to 1 turn as per filter instructions.
- Replace the drain plug, refill with the recommended oil amount and type for the Fit, and run the engine to check for leaks.
- Shut off the engine and recheck oil level; top off if necessary and dispose of used oil and filter at a proper facility.
Make sure to reset the oil change indicator if your model has one and dispose of the old oil and filter responsibly.
Summary
For a 2009 Honda Fit, the standard recommendation is to use Honda's OEM engine oil filter for the 1.5L i-VTEC engine. Typical OEM part numbers are 15400-PLM-A02, with 15400-PLM-A01 seen on some production runs. If opting for aftermarket, verify compatibility with the 1.5L Fit and cross-reference with the retailer. When in doubt, check the VIN or consult a parts professional to confirm the correct filter for your exact vehicle.
What size are Honda oil filters?
Measurements
| Item Dimensions | 10 x 6 x 1 inches |
|---|---|
| Thread Size | M14x1.5 |
| Item Weight | 0.2 Pounds |
What oil filter does a 2009 Honda Fit take?
15400-PLM-A02) Genuine Honda original equipment oil filter for your Honda vehicle. Engineered and specified by Honda, this is the same filter as that which would be installed by your dealer.
What does the PH7317 oil filter fit?
Broad Compatibility: The PH7317 filter fits a wide range of Honda, Subaru, Nissan, and Acura vehicles from 2001 to 2023.
What kind of oil does my 2009 Honda Fit use?
5W-20
Oil Grade: API*
| Viscosity: | 5W-20 (All TEMPS) |
|---|---|
| Capacity: | 3.8 quarts (with filter). After refill check oil level. |
| Capacity: | 3.6 quarts. w/of. After refill check oil level. |
| Torque: | 29 ft/lbs (Oil Drain Plug) |