The 2015 Wrangler with the 3.6L Pentastar engine uses a Fram oil filter in the 7317 size family. Common Fram part numbers that are listed as compatible include PH7317A (Extra Guard), XG7317 (Ultra Synthetic), and TG7317 (Tough Guard). Always verify compatibility with Fram’s official catalog or by checking your vehicle’s VIN.
Fram offers several filter lines that are advertised as fitting the 3.6L Jeep Wrangler. The exact match can vary by trim, market, and production batch, so it’s important to confirm with the latest Fram cross-reference before purchasing. This article highlights the widely reported options and how to confirm you’ve got the right part.
Common Fram Filter Options for the 3.6L Wrangler
Below are Fram filters that are commonly listed as compatible with the 2015 Wrangler’s 3.6L engine. Use these as a starting point, but always double-check with Fram’s catalog or a trusted retailer.
- Fram PH7317A Extra Guard oil filter
- Fram XG7317 Ultra Synthetic oil filter
- Fram TG7317 Tough Guard oil filter
These 7317-sized filters are popular because they fit multiple 3.6L Pentastar applications across different model years. Packaging and listings may vary by region, so confirm the exact part number before buying.
How to Confirm Compatibility
Before you buy or swap filters, follow these steps to ensure you’re selecting a Fram model that fits your 2015 Wrangler with the 3.6L engine.
- Identify your exact vehicle configuration (model year, engine, and trim) using the VIN or owner’s manual.
- Check the current filter’s size, thread type, and gasket to compare with common 3/4-16 thread etiquette used on the 3.6L Pentastar.
- Visit Fram’s official website or a trusted catalog to cross-reference 7317-series filters (PH7317A, XG7317, TG7317) for 2015 Wrangler JK or related 3.6L applications.
- Verify the filter’s packaging part number matches what you intend to purchase (some retailers list multiple compatible Fram SKUs for the same size).
- When in doubt, ask the retailer or consult a service manual to avoid misfit due to regional variations or aftermarket changes.
Following these checks helps prevent ordering the wrong filter and ensures you maintain the Wrangler’s oil system as designed.
Installation Tips
To install a Fram filter correctly, follow these practical steps to minimize leaks and ensure proper oil flow.
- Warm up the engine briefly, then turn off and place a drain pan beneath the filter site.
- Carefully remove the old filter using an appropriate filter wrench, letting excess oil drain into the pan.
- Prepare the new Fram filter by lightly coating the rubber gasket with clean oil.
- Thread the new filter by hand until it seats, then tighten according to the manufacturer’s guidelines (usually 3/4 to 1 turn after contact).
- Replace the crush washer on the oil drain plug if applicable, refill with the recommended oil amount and viscosity, and start the engine to check for leaks.
- Dispose of used oil and the old filter properly and reset any maintenance reminders if applicable.
Choosing the right Fram filter and installing it correctly helps maintain optimal engine lubrication and performance for your 2015 Wrangler.
Notes on Choosing Between Fram Lines
Fram’s Extra Guard (PH7317A), Ultra Synthetic (XG7317), and Tough Guard (TG7317) all meet basic filtration needs for the 3.6L Wrangler. The Ultra line generally offers higher filtration efficiency and longer service life, while Extra Guard provides solid everyday protection. The Tough Guard line emphasizes durability. Your choice may depend on driving conditions, maintenance intervals, and personal preference.
Summary
For a 2015 Jeep Wrangler with the 3.6L Pentastar engine, Fram’s 7317-size filters are the primary compatibility family. Commonly listed options include PH7317A (Extra Guard), XG7317 (Ultra Synthetic), and TG7317 (Tough Guard). Always verify exact fit using Fram’s cross-reference, your VIN, and retailer packaging before purchasing. With the right filter and proper installation, you’ll help maintain the Wrangler’s engine health and performance.