In most Honda City models, you turn on cruise control, reach your desired speed, and press SET to lock it in; you can adjust with RES/+ and SET/-, and cancel with the brake or a dedicated CANCEL/OFF control.
Quick-start guide for conventional cruise control
The following steps cover the standard, non-adaptive cruise control setup found on many City trims. If your car uses adaptive cruise control, see the ACC section below for differences.
Before you begin, make sure you’re on a clear highway or straight road with light traffic. Cruise control is intended for steady-speed driving and should not replace active attention to the road.
- Step 1: Turn on the cruise control system using the steering-wheel controls or stalk labeled CRUISE/ON. Look for an indicator on the instrument cluster confirming the system is active.
- Step 2: Accelerate to your desired cruising speed with the accelerator pedal. A minimum speed is typically required (often around 40 km/h / 25 mph).
- Step 3: Press SET (or SET/−) to lock in the current speed. The vehicle will maintain that speed automatically unless you cancel it.
- Step 4: To increase or decrease speed, use the RES/+ to resume or raise speed and the SET/− to reduce speed.
- Step 5: To disengage, press CANCEL or briefly touch the brake pedal. The system will deactivate but retain the previously set speed for a later resume in most cases.
- Step 6: To resume the previously set speed, press RES or +. If you had canceled, this returns you to the stored speed.
- Step 7: To completely turn off cruise control, press OFF or switch the control to the OFF position (varies by model).
These steps describe the standard workflow for conventional cruise control on Honda City models. Always refer to your owner’s manual for the exact controls on your year and trim.
Adaptive Cruise Control (ACC) and Honda Sensing variants
Some newer Honda City models available in select markets include Adaptive Cruise Control (ACC) as part of Honda Sensing. ACC can maintain a set speed while automatically adjusting to keep a safe gap from the car ahead. If your City has ACC, controls and behavior differ slightly from conventional cruise control.
Before using ACC, ensure it is enabled in the vehicle’s settings and familiarize yourself with its distance settings and limitations. The following guide outlines typical ACC use, but exact steps can vary by year and market.
- Step 1: Activate ACC using the steering-wheel controls (often a button labeled CRUISE/ACC) and, if equipped, enable Honda Sensing features.
- Step 2: Set your cruising speed with SET or a similar control, then adjust the following distance using the distance/DRIVE button or selector provided on the steering wheel or dash.
- Step 3: The system will automatically adjust speed to maintain the chosen gap to the vehicle ahead. If traffic slows or stops, some City configurations can slow down or stop and resume under certain conditions.
- Step 4: To deactivate ACC, press CANCEL or OFF or apply the brake. You can usually resume at the previously set speed with RES or the resume control.
ACC features and their behavior depend on the specific model year and market. If your City is equipped with Honda Sensing or ACC, consult the owner’s manual for the exact operation and any limitations.
Market differences and safety tips
Engineers ship Honda City variants with different levels of cruise control capability depending on the region and model year. The following notes help you verify what yours can do and how best to use it safely.
- Check your owner’s manual or the instrument-cluster menus to confirm whether cruise control or ACC is included in your trim.
- Some older City models use a stalk behind the steering wheel for cruise control rather than wheel-mounted buttons; others place controls on the steering wheel itself.
- In all cases, cruise control is a convenience feature and not a substitute for attentive driving. Use it on suitable roads and when weather and traffic conditions are favorable.
- The brake pedal typically overrides and cancels the system, and a brief touch on the brake or a CANCEL action will disengage it.
For precise operation in your car, check the manual or contact a Honda dealer to confirm the exact controls for your year and market.
Summary
Most Honda City models with cruise control allow you to turn the system on, reach a steady speed, and press SET to lock that speed in. You can adjust with RES/+ and SET/−, and cancel with the brake or a cancel control. In markets where ACC is available, you’ll also manage a following distance and benefit from automated speed adjustments relative to the car ahead. Always verify features for your exact year and trim and use cruise control only under appropriate road and traffic conditions.