In a 2019 Honda Accord, you can view each tire’s current pressure via the Tire Pressure Monitoring System (TPMS) readout on the instrument cluster or the center display. You can also confirm actual pressures with a handheld gauge and compare them to the recommended settings listed on the door jamb placard.
The Accord uses TPMS to monitor tire pressure and alert you if a tire drops significantly below the recommended level. Below are practical ways to check the pressures inside the car, plus how to verify with a gauge and where to find the official numbers.
View tire pressures on the instrument cluster
What you’ll see on the dash
In models with the driver information display, you can pull up a tire pressure screen that shows each tire’s current psi. This is the quickest way to confirm whether any tire is underinflated without tools.
Before you begin the process, note that you should check pressures when the tires are cold for the most accurate readings. The steps below walk you through accessing the TPMS readout from the instrument cluster.
Use the following steps to view tire pressures on the instrument cluster:
- Turn the ignition to the ON position (engine off) or start the car if needed for the display to wake up.
- Press the information/menu button on the steering wheel to access the Vehicle Information menu.
- Scroll to and select "Tire Pressure" or "TPMS" to display the current pressures for front-left, front-right, rear-left, and rear-right tires in psi.
- Compare the shown values to the door jamb placard (see below) to determine if inflation is needed.
After you view the readings, you can act on them by inflating tires that are low and then driving briefly to allow the system to refresh. If a warning light is on, address it promptly by bringing tires to the recommended pressures.
View tire pressures using the center display or touchscreen
Navigating the TPMS on the display audio/i-MID
Some Accord trims with the larger touchscreen present TPMS information on the main display under the Vehicle or TPMS menu. This provides another route to see each tire’s pressure.
Before using the touchscreen, prepare to verify the numbers against the tire placard. The steps below describe a typical path on models with the larger display:
- Turn the ignition to ON and wake the display.
- From the Home screen, select Menu or Vehicle, then locate TPMS or Tire Pressure information.
- Open the Tire Pressure screen to view each tire’s pressure in psi.
- Use this readout to confirm whether any tire is underinflated and needs air, referencing the door placard for the correct target pressures.
After inflating or verifying via the center display, take a short drive to allow the TPMS to update and confirm the new readings.
Manual verification with a tire pressure gauge
Why and how to measure with a gauge
TPMS readings are convenient, but it’s best to confirm with a physical tire pressure gauge, especially when tires are cold or you suspect a leak. An accurate gauge helps ensure you’re inflating to the correct level.
Follow these steps to measure and adjust tire pressures with a gauge:
- Check tire pressure only when the tires are cold (vehicle has not been driven for several hours). Remove the valve cap from a tire.
- Press a digital or analog gauge onto the valve stem and note the reading in psi.
- Inflate or deflate the tire to the recommended cold pressure printed on the door jamb placard.
- Repeat for each tire, then recheck all four readings after letting them settle for a moment.
If you adjust pressures, reset your expectations by driving a short distance to allow the system to reflect any changes and re-check if necessary.
Where to find the recommended tire pressures
Knowing the exact targets for your tires is essential. The Accord’s recommended pressures are specified by tire size and load, and you’ll find them in these places:
- Door jamb placard on the driver’s side, which lists front and rear cold tire pressures specific to your vehicle’s tires.
- Owner’s manual, which covers general TPMS guidance and any variations for trims or tire sizes.
Note that the exact numbers can vary by model year, trim level, and installed tires. In most cases, you’ll see a typical range in the low-to-mid 30s psi, but always rely on the placard for your car.
Summary
The 2019 Honda Accord provides multiple, straightforward ways to check tire pressure: a built-in TPMS readout on the instrument cluster, optional TPMS access via the center display, and manual verification with a gauge. Always start with the door jamb placard for the correct target pressures, check tires when cold, and adjust as needed. Regular checks help maintain safety, fuel efficiency, and tire life.