In a 2017 Honda Civic, the Tire Pressure Monitoring System (TPMS) can be reset by ensuring all tires are inflated to the recommended cold pressures and then either calibrating the system through the vehicle’s settings or performing a highway relearn by driving. The exact method can depend on trim level and whether the car has an onboard TPMS calibration option.
Understanding TPMS on the Civic
TPMS monitors each tire’s pressure and warns you if any tire is underinflated. After inflating tires, rotating wheels, or replacing tires, the system may need to relearn the new pressures so the warning light shows correctly. Some 2017 Civics provide a dedicated calibration option in the settings, while others rely on a driving relearn initiated by normal highway driving.
What you’ll need
Before attempting a reset, gather the necessary items and confirm you know the recommended cold pressures for each tire from the door jamb placard or owner’s manual.
- A tire pressure gauge to verify exact psi
- A source of air to inflate tires to spec
- Knowledge of the correct cold-inflation pressures for all tires
- Access to the vehicle’s Settings/TPMS menu (if your model supports on-screen calibration)
Cold pressures are measured when the vehicle has not been driven for several hours. Pressures can vary by load, wheel size, and tire type, so always use the placard values as the standard.
Two common methods to reset TPMS
There are two standard approaches for the 2017 Civic: using an onboard TPMS calibration option (if your trim supports it) or performing a highway relearn by driving after aligning tire pressures.
Method 1: Onboard TPMS calibration (if available on your trim)
Use this method if your Civic’s instrument cluster or infotainment system includes a TPMS Calibration option. It directly recalibrates the sensors with the vehicle’s computer.
- Turn the ignition to ON and engine OFF (do not start the engine).
- Access the vehicle’s settings menu via the steering wheel controls or touchscreen.
- Select the TPMS Calibration or Tire Pressure Monitor Calibration option.
- Choose Calibrate or Reset and confirm your choice.
- Drive the car at a steady speed (roughly 40–60 mph / 64–97 km/h) for 10–20 minutes until the TPMS indicator stops blinking or goes out.
After attempting this method, the system should be relearned. If the light remains on or the calibration option is not available, continue with Method 2 or consult a dealer.
The onboard calibration method is the quickest path when your Civic supports it, and it avoids potential sensor-related issues by using the car’s own learning cycle.
Method 2: Highway relearn (no onboard calibration required)
If your trim doesn’t offer a TPMS calibration option, performing a highway relearn after inflating tires to the correct pressures often resets the system automatically.
- Inflate all tires to the recommended cold pressures listed on the door jamb placard.
- Start the engine and begin driving on a highway at a steady speed (typically 50 mph / 80 km/h or higher).
- Maintain highway speeds for about 10–20 minutes, avoiding abrupt accelerations or decelerations.
- Pull over, check the TPMS warning light. If the light goes out, the relearn is complete; if it remains on, recheck tire pressures and repeat the drive.
Note: Some vehicles may require a longer or repeated highway run for a full relearn. If the light persists after a reasonable attempt, there may be a sensor issue or a slow leak that needs attention.
Troubleshooting and when to seek help
If the TPMS light stays on after trying the above methods, consider these checks:
- Recheck all tire pressures when tires are cold to ensure accuracy.
- Look for tire leaks, punctures, or damaged valves that could cause persistent low pressure.
- Inspect for a faulty TPMS sensor or a dead sensor battery, which may require service or sensor replacement.
- Contact a Honda dealer or qualified mechanic if the TPMS cannot be reset or if the warning light stays on after multiple relearns.
Summary
Resetting TPMS on a 2017 Honda Civic typically involves inflating all tires to the recommended cold pressures and either using an onboard TPMS calibration option or performing a highway relearn. If your model supports the in-dash calibration, follow the on-screen steps; otherwise, a steady highway drive after correct inflation usually enables the relearn. If issues persist, check for leaks or sensor faults and seek professional help as needed.