Inflate all tires to the vehicle’s recommended pressures and perform a TPMS relearn using either the physical TPMS reset button found in many older Honda models or the TPMS calibration option in the car’s settings on newer models. After the relearn, drive at highway speeds to complete the process. If the warning light stays on, there may be a faulty sensor or a deeper issue.
The exact procedure depends on model year and trim. This guide outlines the most common methods used across Honda vehicles, with notes for popular models such as the Civic, Accord, CR‑V, and Pilot. Always consult your owner’s manual for the precise sequence for your car.
Common TPMS reset methods
Below are the two primary approaches you’ll encounter on most Honda models. Each method begins with ensuring correct tire pressures and ends with a highway-drive relearn.
- Method A: TPMS reset button (older Honda models)
- Locate the TPMS reset button. It is often near the steering column, under the dashboard, or inside the glove box area.
- With the ignition on and the engine off, press and hold the TPMS button until the indicator light on the dash blinks or confirms the reset (patterns vary by model).
- Release the button and wait a few minutes, then drive at a steady speed (about 50–60 mph / 80–100 km/h) for around 10 minutes to complete the relearn.
- Check that the TPMS light goes off once the relearn is successful.
- Method B: TPMS calibration via settings (newer Honda models)
- With the tires inflated to the recommended pressures, access the vehicle’s settings menu (often via the Driver Information Center or infotainment screen).
- Navigate to Settings › Vehicle (or Vehicle Settings) › TPMS Calibration (or TPMS Relearn) › Calibrate (or Relearn).
- Confirm the calibration, then turn off the ignition for a moment and restart the car.
- Drive at highway speed (about 50–60 mph / 80–100 km/h) for 10–20 minutes to complete the relearn.
- Verify the TPMS light is off after a successful relearn.
These methods cover the majority of Honda models in recent years. If your model uses a slightly different path in the menu, the concept is the same: inflate to spec, initiate relearn via a button or the vehicle’s settings, then drive to finalize the process.
Additional notes and what to do if it doesn’t work
If the TPMS light stays on after attempting a reset, consider these steps before visiting a technician:
- Double-check tire pressures at a reliable gauge and re-inflate to the recommended level on the door jamb placard.
- Inspect for slow leaks or punctures that could keep a tire from seating at the correct pressure.
- Inspect the wheel sensors visually for damage or corrosion at the valve stem.
- If multiple tires were recently serviced or replaced, ensure proper sensor programming for those wheels.
- Consider using a professional TPMS tool or visiting a dealership if the light persists, as a sensor fault or a dead battery in a sensor can require replacement.
The TPMS relies on wheel sensors and a receiver in the vehicle, and occasional faults can occur after tire changes, battery disconnections, or sensor aging. If you’re unsure about the procedure for your exact model year, consult the owner’s manual or contact a Honda service center for model-specific instructions.
Model-specific notes
Civic
Most Civics released in the last decade support TPMS calibration through the Settings menu. If your Civic uses the old reset button, follow the button method first, then perform a highway relearn to confirm the system.
Accord
Accord models across several generations can require either a button-based relearn or a settings-based calibration. If the light persists after a standard relearn, there may be a sensor issue or a need for reprogramming of the system.
CR‑V
CR-V vehicles commonly use the calibration path in the instrument cluster or a dedicated TPMS option in the infotainment system. Ensure all tires (including the spare, if equipped with a TPMS) are within spec before starting.
Pilot
Pilots may show the TPMS calibration option under Vehicle Settings. If you rotated rims or replaced tires, a relearn is typically required to re-sync the sensors.
Summary
Resetting a Honda TPMS generally involve two routes: a physical reset button on older models or the vehicle’s internal TPMS calibration in newer models. Start by inflating all tires to the recommended pressures, then perform the relearn via the appropriate method and complete the process with a highway drive. If the warning persists, check for leaks, sensor damage, or faulty sensors and seek professional assistance if needed.