Inflate all four tires to the recommended cold pressures and reset the TPMS either with a dedicated reset button (if your trim has one) or by driving to trigger an indirect relearn. The warning light should go out once the system relearns.
For the 2016 Honda CR-V, the precise method depends on the trim level and whether the vehicle includes a TPMS reset switch. The procedure generally falls into two paths: a manual reset using a TPMS button, or an indirect relearn that occurs automatically when the vehicle is driven at highway speeds after pressures are corrected. Below are the commonly used methods and the steps to follow.
Understanding TPMS and what triggers the light
TPMS stands for Tire Pressure Monitoring System. It monitors the air pressure in each wheel and alerts you when a tire is underinflated or when a sensor fault is detected. In most 2016 CR-Vs the light comes on when a tire drops below the recommended pressure by about 25% or if a sensor is faulty after a tire change, rotation, or a sensor battery failure.
Reset options for the 2016 CR-V
Before attempting a reset, make sure all four tires are inflated to the recommended cold pressures and that there are no punctures or slow leaks. Also, ensure the vehicle's battery is stable and the tires are evenly inflated.
With a TPMS reset button (if equipped)
If your 2016 CR-V has a dedicated TPMS reset button, use this method to recalibrate the system manually.
- Inflate all four tires (do not rely on the spare) to the recommended cold pressures listed on the door jamb sticker or in the owner's manual.
- With the ignition on and the engine off, locate the TPMS reset button (often labeled TPMS or with a tire icon) on the dashboard or lower left side of the instrument panel.
- Press and hold the button until the TPMS indicator on the instrument cluster blinks once or twice, indicating the system is in relearn mode, then release.
- Drive at speeds above 30 mph (50 km/h) for about 10 minutes or until the warning light stops blinking and goes out.
When successful, the light should disappear and the system will be calibrated to the new pressures. If the light remains, recheck pressures and consider seeking service.
Indirect relearn (no reset button)
If your CR-V lacks a TPMS reset button, you typically rely on the indirect relearn by driving after correcting pressures. The steps below describe the common approach.
- Inflate all four tires to the recommended cold pressures.
- With ignition on (engine off), ensure the vehicle is in Park and start a highway driving session at steady speeds: drive for 10–20 minutes at 50–60 mph (80–100 km/h) or longer if needed.
- Stop and check the instrument cluster. If the light is still on, drive again for a few more minutes; the system should automatically relearn and the light will turn off once complete.
Note: Some vehicles may require additional steps or a dealer-level reset if the light does not go out after a proper relearn cycle.
Troubleshooting: light stays on or reappears
If the TPMS light stays on after a successful relearn or if it comes back after a short time, it may indicate a sensor issue, a damaged wheel sensor, or a slow leak in one tire. In that case, inspect tires for punctures, check the valve stems, and consider professional tire service or sensor replacement. Also, a recent tire rotation or replacement can require a reset to learn new sensor IDs.
When to seek service
Seek service if the light remains on after attempts, if you notice a sudden drop in tire pressure without a cause, or if you suspect sensor battery failure (TPMS sensor batteries typically last several years). A dealership or qualified shop can diagnose using a TPMS scan tool and replace sensors if needed.
Summary
Resetting the tire pressure light on a 2016 Honda CR-V involves correcting all tire pressures to the recommended levels and performing a TPMS relearn. Depending on your trim, use a dedicated TPMS reset button or rely on an indirect relearn by driving at steady highway speeds. Always verify the light is off after the relearn and consult the owner's manual or a dealer if the warning persists.
How do you turn off the tire pressure light on a 2016 Honda?
Start the car back. Up. No more indicator. Light. It's pretty simple this will work on a 16 Accord uh I think it'll work from a 13 up also and a lot of other Honda models have the same button.
Where is the TPMS reset button on a Honda CRV?
Position. Step two now look down to the left side of your dashboard. Just under the steering wheel. You'll see a little button that looks like a horseshoe with an exclamation.
How to remove low tire pressure indicator after tire change in CRV 2017?
Point simply press and hold the button for a few seconds. While holding it keep an eye on the TPMS. Light on your dashboard. Once it blinks twice and disappears.
How to reset low tire pressure light on 2016 Honda CR-V?
Put into calibrate. Hit enter calibration started now all you have to do is drive the car and it will automatically calibrate the TPMS sensors. Thanks for watching.