In most 2016 CR-V models, there isn’t a dedicated TPMS reset button. The system usually relearns automatically after you inflate all tires to the recommended cold pressures and drive at highway speeds for several minutes. If the warning light stays on after that, there may be a tire pressure issue or a sensor fault that requires further diagnosis.
What TPMS is and how it works on the 2016 CR-V
The Tire Pressure Monitoring System (TPMS) warns you when one or more tires are underinflated. On many 2016 CR-Vs, there is no manual reset procedure you can perform from the cabin; the system relearns as you drive with properly inflated tires. If a tire is replaced, rotated, or a sensor is replaced, the vehicle may require a relearn or diagnostic check with a TPMS tool. Note that the spare tire typically does not have a TPMS sensor, so it is generally not part of the relearn process unless your specific model includes a sensor-equipped temporary spare.
When you might need to relearn the TPMS
Relearning or resetting is typically needed after inflating tires to spec, after a tire rotation, or after replacing a tire or TPMS sensor. If you’ve recently adjusted pressures or swapped tires and the light remains on, you’ll want to follow the steps below and then monitor the system during normal driving. If the warning persists after a full relearn attempt, professional diagnostics are recommended.
Step-by-step relearn procedure
Use these steps to help the TPMS relearn after you’ve corrected tire pressures. Keep in mind that some 2016 CR-V vehicles do not have a manual reset switch, so the relearn is often accomplished by driving with properly inflated tires.
- Check all tires (including the spare if it has a sensor) and inflate each one to the recommended cold pressure listed on the doorjamb placard or in the owner’s manual.
- Ensure the tires are cool when you measure and adjust pressures to avoid overinflation from heat buildup.
- Drive the vehicle at highway speeds (roughly 50 mph or higher) for about 10–15 minutes to allow the TPMS to relearn the new pressures.
- If the warning light turns off during or after the drive, the relearn is complete. If the light remains on, repeat the drive at highway speeds for another 10–15 minutes and check again.
After completing these steps, the TPMS should reset if the system is functioning normally and all pressures are within specification. If the light still stays on, there may be a faulty sensor, a leak, or a need for a dealer diagnostic tool to perform a TPMS relearn or sensor replacement.
Troubleshooting a persistent TPMS warning
If the TPMS light remains illuminated after following the relearn steps, try these checks or actions to narrow down the cause:
- Inspect tires for slow leaks or punctures and verify all inflation levels again. A small puncture or a slow leak can keep the light on.
- Check wheel sensors and wiring for damage, especially after a tire change or wheel work. Corroded or damaged sensors can fail to relay data.
- Confirm the spare tire’s status. In most CR-V models, the temporary spare does not have a TPMS sensor; if you are relying on the spare for a long period, the system may detect imbalanced pressures when you switch back to the normal tires.
- If no obvious tire issue is found, have a tire shop or Honda dealer diagnose the TPMS with a dedicated scan tool. They can read sensor codes, relearn the sensors, and replace defective components if needed.
Conclusion: A persistent TPMS warning usually points to underinflation, a slow leak, or a faulty sensor. Properly inflating tires and driving to relearn will often clear the warning, but persistent warnings should be evaluated by a professional to prevent driving with underinflated tires.
Summary
For a 2016 Honda CR-V, there is typically no manual TPMS reset button. Ensure all tires (and the spare, if sensor-equipped) are inflated to the manufacturer’s recommended cold pressures, then drive at highway speeds for 10–15 minutes to allow the system to relearn. If the light remains on after a full relearn attempt, inspect for tire leaks or sensor issues and consult a dealer or tire shop for a diagnostic and potential sensor replacement.