The TPMS light on a Honda Fit is typically reset by ensuring all tires are properly inflated and then allowing the system to recalibrate, either automatically through driving or via a manual calibration option in some model years. If the light persists after correcting pressures, a manual reset or a dealer check may be needed.
Understanding TPMS and why reset is sometimes necessary
The tire pressure monitoring system (TPMS) warns you when a tire is underinflated or when a sensor isn’t reading correctly. After adjusting tire pressures or replacing tires, the system may need a recalibration so it can accurately monitor the tires again. Depending on the model year and trim, Honda Fit vehicles can reset automatically through normal driving, or may require a manual calibration via the vehicle’s settings menu.
Automatic recalibration by driving
Before beginning the listed steps, note that many Honda Fits recalibrate automatically once tires are inflated to the correct pressures and you drive for a while. If your car supports automatic recalibration and the pressures are correct, this is often the simplest path.
- Ensure all four tires (and the spare, if it’s sensor-equipped and used) are inflated to the recommended cold pressure printed on the door jamb placard or in the owner's manual.
- Start driving and maintain highway speeds (roughly 50–60 mph / 80–100 km/h) for about 10–20 minutes to allow the system to relearn each tire's new pressure state.
- Monitor the dashboard; if the TPMS light goes out after the drive, the recalibration is complete. If it stays on, proceed to the manual calibration steps or consult a dealer.
Concluding: Automatic recalibration is the first option on many Fits. If the light remains after proper inflation and a highway drive, try the manual calibration route or seek service to check for sensor or system issues.
Manual TPMS calibration (where available)
Some Honda Fit model years offer a manual calibration option in the instrument panel or settings menu. If your vehicle has this feature, you can initiate a calibration without heavy driving, though a final highway drive is often still required to complete the process.
- Check the instrument cluster or information display for a TPMS Calibration or TPMS Reset option. Navigate to Vehicle Settings or TPMS, then select Calibrate/Initialize. If you don’t see this option, your model may not support manual calibration.
- If your Fit has a dedicated TPMS button (often located on the lower left area of the dash near the steering column), you may be able to press and hold it for a few seconds to start the reset procedure. If present, refer to the owner’s manual for exact timing.
- Confirm the calibration and then drive at highway speeds to complete the relearning process. The light should extinguish once the system finishes recalibrating.
Concluding: Manual calibration is model-year dependent. If your vehicle supports it, follow the on-screen prompts or owner’s manual. If not, rely on the automatic recalibration path and a highway drive.
What to do if the light stays on or you suspect a fault
If the TPMS light remains illuminated after you’ve inflated tires to the correct pressures and attempted both automatic and manual calibration, there could be a sensor fault or a dead sensor battery, a damaged wheel, or a TPMS control module issue. In that case, schedule a diagnostic with a Honda service center or a qualified tire shop to inspect sensor integrity, valve stems, and electrical connections before driving long distances.
Summary
Resetting the TPMS on a Honda Fit generally starts with inflating all tires to the recommended cold pressures and then driving to allow automatic recalibration. Some model years also offer a manual TPMS calibration in the vehicle’s settings or via a dedicated button. If the light persists after correct inflation and following either path, seek professional service to check for sensor or system faults. Regularly monitoring tire pressures is the best way to prevent TPMS warnings from reoccurring.
How to reset TPMS light on 2011 Honda Fit?
Point that's your TPMS reset button press and hold this TPMS button until the TPMS light on your dashboard blinks twice and your TPMS. Light should turn off after that you can release the button.
How to reset TPMS on 2016 Honda Fit?
Pressure. And to reset that or recalibrate there's a button on the lower left of the Honda Fit. You press and hold for about 3 to 5 seconds. And the button also matches the the logo on the gauge.
How to reset the TPMS light on a 2020 Honda Fit?
Steps to Reset Honda TPMS Lights in Newer Models
- From the Home screen, select “Settings”
- Select your vehicle.
- Select “TPMS Calibration”
- Select “Calibrate”
Where is the TPMS reset button on a Honda Fit?
And now when we look back up here The light blinks twice. And then turns. Off. So that's all we have to do once that lights off the system will automatically re-calibrate itself while as you drive.