The tire pressure warning can be reset after you’ve inflated all tires to the correct cold pressures and performed a relearn of the system. In most cases, the light clears once the TPMS recognizes the tires are at the proper pressures and the sensors relearn their positions.
This article explains what the TPMS does, where to find the reset control, the exact steps for the 2016 Accord, and common issues that can prevent a successful reset.
Understanding TPMS on the 2016 Accord
The Tire Pressure Monitoring System (TPMS) monitors each wheel’s air pressure and alerts you if a tire is underinflated or if there’s a sensor fault. The 2016 Accord uses direct TPMS sensors in each wheel, which means a physical sensor in each tire sends data to the car’s computer. A reset is often needed after inflating tires or replacing sensors or tires.
Direct vs indirect TPMS
Direct TPMS uses wheel-mounted sensors to measure actual air pressure, while indirect TPMS infers pressure levels from wheel speed sensors. The 2016 Accord relies on direct sensing, so a proper reset requires inflating to specification and initiating a relearn procedure.
Reset procedure for the 2016 Honda Accord
Before you begin, make sure all tires are correctly inflated and you know the recommended pressures from the door jamb placard. Also locate the TPMS reset control for your trim level; if you can’t find a reset button, consult the owner’s manual because some models rely on the vehicle’s built-in relearn process rather than a dedicated switch.
- Inflate all tires to the recommended cold pressures listed on the driver’s door placard. Check pressures when the tires are cold (not after a drive). Adjust as needed until every tire matches the specified value.
- Find the TPMS reset control. On many 2016 Accords, the reset button is on the left side of the instrument panel near the hood release, labeled “TPMS.” If you don’t see a dedicated switch, the reset may be performed via the vehicle’s settings menu or the dealer may need to assist.
- Turn the ignition to ON with the engine OFF. Press and hold the TPMS button until the TPMS indicator light in the dashboard blinks or flashes, then release the button.
- Start the engine and drive at highway speeds (around 50 mph/80 km/h or higher) for about 10 minutes to relearn the tire positions and complete the reset process. The light should go out once the system recognizes the inflated tires.
- If the light remains on after this cycle, repeat steps 1–4. If it still won’t reset, recheck tires for leaks, ensure sensors are not damaged, and consider a professional diagnostic with a TPMS tool to verify sensor IDs and pressures.
Some models or trims may require a longer relearn drive or a specific sequence accessed through the infotainment system. If you have a service manual for your exact trim, follow those instructions or contact a Honda dealer for guidance.
Troubleshooting and caveats
If you still see the warning after a reset, several issues could be at play. Addressing these first can help avoid repeated resets or sensor failures.
Representative issues
- Underinflated tire or slow leak not yet detected
- Damaged or failed TPMS sensor in one wheel
- Tires recently replaced or rotated without reprogramming sensors
- Extreme cold affecting tire pressure readings
If any of these issues are suspected, inspect tires for cuts, punctures, or leaks, and have sensors tested or replaced as needed. A tire shop or Honda dealer can perform a diagnostic with a TPMS tool to confirm sensor health and IDs.
When to seek professional help
If after multiple attempts the TPMS light remains on, a professional diagnosis is warranted. A dealer or qualified tire service center can reprogram TPMS sensors, replace faulty sensors, or update the vehicle’s TPMS software if required. This is especially important after replacing tires, sensors, or wheels, as mismatched sensor IDs can prevent a successful relearn.
Summary
Resetting the 2016 Honda Accord’s tire pressure light involves inflating all tires to the recommended cold pressures and performing a relearn using the TPMS control or the vehicle’s setup procedure. Drive at highway speeds for about 10 minutes to complete the relearn; if the light stays on, inspect tires for leaks, check sensor health, and seek professional help if necessary. Regularly checking tire pressures and keeping them within the recommended range helps prevent false alarms and extends tire life.