The 2019 Hyundai Tucson with a 2.4-liter engine uses about 4.5 quarts (roughly 4.3 liters) of engine oil when you perform a full oil and filter change. This figure is a practical guideline, with exact capacity depending on whether you include a new filter or simply drain the oil.
Official capacity and variations
Hyundai provides guidance that typically centers on two numbers: the standard oil fill with a new filter and a lower figure if you drain oil only without replacing the filter. The following figures reflect common service data for the 2.4 L engine used in the 2019 Tucson.
- With oil filter: 4.5 qt (4.3 L)
- Without oil filter: 4.0 qt (3.8 L)
In practice, plan on about 4.5 quarts to complete a normal oil change. For the exact specification on your particular vehicle (VIN and market can affect numbers), consult the owner's manual or a Hyundai service bulletin.
Oil grade and climate considerations
While the capacity is the same, the recommended oil viscosity can vary by climate and model year. Check the owner's manual for the precise grade your region requires (for example, many 2.4 L Tucson engines in North America are paired with a 5W-20 or 5W-30 formulation, depending on environmental conditions). Using the correct viscosity helps ensure optimal protection during starts and in temperature extremes.
Change oil: step-by-step
If you’re performing the oil change yourself, here is a standard sequence to follow. This list assumes you’re replacing the filter as well as draining the oil.
- Warm up the engine for a few minutes to loosen oil, then turn off and secure the vehicle.
- Raise the Tucson safely on a flat surface and support it with stands if needed.
- Place a drain pan beneath the oil pan; remove the drain plug and allow the old oil to fully drain.
- Remove the old oil filter; prepare the new filter by lightly coating its gasket with fresh oil.
- Reinstall the drain plug securely, then begin pouring in new oil. Start with about 4.5 quarts (4.3 L) as a target.
- Install the new oil filter and continue adding oil until the dipstick shows the full level.
- Start the engine, run for 1–2 minutes, then turn off and wait a minute. Recheck the oil level and add more if needed to reach the full mark.
After completing the change, carefully dispose of the used oil and filter at an appropriate recycling facility or service center.
Post-change checks and tips
Always verify the oil level with the dipstick after the engine has cooled slightly and been re-run. If you notice leaks around the drain plug or filter, address them before driving. Keeping a regular oil-change schedule helps maintain engine health and performance.
Safety and disposal tips
Follow local regulations for oil disposal and recycling. Use manufacturer-recommended oil grade and viscosity, and avoid overfilling the crankcase, which can cause high pressure and leaks. If in doubt, consult a Hyundai dealer or certified mechanic for a precise specification for your vehicle’s VIN.
Summary
For a full oil change on a 2019 Hyundai Tucson with the 2.4 L engine, plan for roughly 4.5 quarts (4.3 L) of engine oil, including a new filter. If you drain oil only and don’t replace the filter, the capacity is closer to 4.0 quarts (3.8 L). Always verify exact figures in the owner's manual and use the recommended oil grade for your climate. Following proper disposal practices and a diligent check of the level after the change will help keep the engine running smoothly.
What kind of oil does a 2019 Hyundai Tucson take?
For example, Tucsons made between 2016 and 2021 incorporate either a 2.0-liter or a 2.4-liter four-cylinder engine. The 2022 and 2023 versions use a similar but slightly larger engine, which is a 2.5-liter four-cylinder engine. All these engines can accept 5W-20 or 5W-30 oil.
Ask about result
Can a Hyundai Tucson take 5W-30 oil?
What Kind Of Oil Does The Hyundai Tucson Use? The correct Hyundai Tucson oil type varies by year and engine, but typically it is full synthetic 0W-20 or 5W-20 oil for the most recent models, with some earlier models recommending 5W-30 full synthetic.
Ask about result
How much oil does a 2019 Hyundai Tucson 2.4 take?
5.1 quarts
Oil Grade: SL
| Viscosity: | 10W-30 (Above -18°C) 5W-20, 5W-30 (All TEMPS) - SAE 5W-20 is preferred. |
|---|---|
| Capacity: | 5.1 quarts (with filter). After refill check oil level. |
| Torque: | 29 ft/lbs (Oil Drain Plug) Install a new washer on the drain bolt. Only use an OE drain plug. |
Ask about result
How much oil does a 2.4 L Hyundai Tucson take?
The 2.4L engine typically requires roughly 4.5–5.0 quarts of oil, depending on filter capacity and drain procedures.
Ask about result