Replacing a throttle body on a Chrysler 200 typically costs between $300 and $900, depending on engine type, parts choice, and labor rates.
The Chrysler 200, produced from 2011 to 2017, offered two engines: a 2.4-liter Tigershark inline-four and a 3.6-liter Pentastar V6. Throttle-body replacement is a common repair that may be performed by independent shops or at a dealership. Prices hinge on parts source (OEM vs aftermarket), regional labor costs, and whether additional related maintenance is required.
What affects the price
The final bill for throttle-body replacement is shaped by several factors. The following considerations often drive the difference between a low-end estimate and a higher one:
- Parts source and type: OEM factory parts versus aftermarket or remanufactured units.
- Engine option: 2.4L Tigershark versus 3.6L Pentastar; different engines may use different parts and pricing.
- Labor costs and time: hourly rate and whether the job requires additional steps or related repairs.
- Shop type and location: dealership rates tend to be higher than independent shops, with regional variations in labor costs.
- Additional maintenance or component work: gaskets, sensors, or throttle-position sensor replacement if needed.
Understanding these factors helps you compare quotes and avoid surprise charges.
Typical cost ranges
Below are general ranges to give you a sense of what drives the total, noting that exact prices will depend on your vehicle and local market.
- Throttle body parts: aftermarket units typically cost 150–350, while OEM or dealer-replaced units commonly run 250–600.
- Labor: replacing a throttle body typically takes 1–2 hours; at independent shops with rates of 75–120 per hour, labor is about 75–240; at dealerships at 120–180 per hour, labor could be 120–360.
- Estimated total (parts plus labor): roughly 300–900 at an independent shop; 600–1300 at a dealership, depending on engine and parts chosen.
Because regional pricing and part choices vary, it’s essential to obtain quotes that break down parts and labor, and to verify what is included in each estimate.
DIY considerations and advice
For a confident DIYer, replacing a throttle body can save on labor, but it requires careful handling to avoid idle relearn issues and air leaks. The following notes help you decide whether to tackle the job yourself.
Tools and preparation
Before you begin, assemble common automotive tools and a method to reset or relearn the throttle position if required by the vehicle's software.
- Basic hand tools (socket set, screwdrivers, pliers) and a repair manual or guide specific to the Chrysler 200 engine variant.
- Vehicle-scanner capable of clearing codes and, if needed, performing throttle-body relearn procedures.
- Correct throttle-body part for your engine (2.4L or 3.6L) and compatible sensors.
If you’re uncertain about relearn procedures or sensor compatibility, professional installation is recommended to ensure reliable idle and drive-by-wire control.
Conclusion: DIY can be cost-saving but carries risk if you don’t perform the relearn correctly or seal the intake properly. A professional installation offers diagnostics and a warranty on parts and labor.
What to ask the shop
When requesting quotes, use this checklist to compare accurately and avoid paying for optional extras you don’t want.
- Whether the quote covers parts and labor and what kind of throttle body is included (OEM vs aftermarket).
- Whether the estimate includes related diagnostics, gaskets, seals, and sensor reinstallation.
- Estimated turnaround time and any vehicle rental options.
- Warranty terms on parts and labor.
Clear questions help ensure the final bill reflects a complete replacement rather than a partial repair.
Summary: For a Chrysler 200, throttle-body replacement costs generally fall into a broad range that depends on engine type, parts choice, labor rates, and who performs the work. Expect roughly $300–$900 at an independent shop, or $600–$1,300 at a dealership, with OEM parts pushing the price higher. Always compare quotes, confirm included items, and consider whether a DIY option or a professional service best fits your situation.
How much is a throttle body for a Chrysler 200?
between $472 and $522
The average cost for a Chrysler 200 Throttle Body Replacement is between $472 and $522. Labor costs are estimated between $107 and $157 while parts are typically priced around $365. This range does not include taxes and fees, and does not factor in your unique location.
What is the most common problem with Chrysler 200?
Owners have reported a wide variety of transmission problems ranging from rough shifting, hesitation during acceleration, and even complete transmission failure. While there have been some recalls issued for some models addressing these issues, problems still persist for others.
Can you drive with a damaged throttle body?
It's not advisable to drive with a malfunctioning throttle body, as it can cause poor acceleration, stalling, and potentially lead to engine damage.
Is it worth fixing the throttle body?
Meanwhile, a dirty throttle body will lead to poor acceleration and bad fuel economy. A bad throttle body makes driving more difficult and can damage other parts, so you should fix it immediately.