You’re likely looking at about $300–$700 to replace a wheel bearing hub on a 2008 Honda CR-V, with front-hub replacements typically costing more than rear, and factors like AWD and parts choice moving the price within that range.
This article breaks down typical costs for the CR-V, explains what influences the final price, and offers practical guidance for planning and getting good value from a repair shop.
Cost overview by component
Prices can vary by whether you’re changing the front or rear hub, the drivetrain configuration (FWD vs. AWD), and the choice between OEM and aftermarket parts. The ranges below reflect typical parts and labor in the United States for a 2008 CR-V at a standard independent shop as of 2024–2025.
- Front wheel hub replacement (front bearing/hub assembly): typically about $260–$660 total. This includes parts plus 1.5–2.5 hours of labor at a shop rate of roughly $75–$125 per hour. Higher-end parts or AWD/four-wheel-drive scenarios can push toward the upper end of the range.
- Rear wheel hub replacement (rear bearing/hub assembly): typically about $150–$520 total. Labor usually runs 1–2 hours, with parts priced lower on average than the front hub, though AWD configurations or premium parts can raise the cost.
In practice, most CR-V owners land somewhere in the middle of these ranges, with AWD systems or OEM hub assemblies adding to the bill. Expect taxes and disposal fees to vary by location and shop policy.
Factors that influence the final price
Several variables can swing the estimate up or down. The following list outlines the key drivers you’ll likely encounter when shops quote your CR-V repair.
- Drivetrain configuration: Front-wheel drive vs all-wheel drive. AWD often requires more labor and sometimes a different hub design, increasing price.
- Part choice: Aftermarket vs OEM (manufacturer) hub assemblies. OEM parts tend to cost more but may offer longer warranty compatibility and exact fit.
- ABS and sensors: Some hub assemblies include ABS tone rings or wheel-speed sensor integration; extra sensors or wiring work can raise costs.
- Labor rate and location: Shop hourly rates vary widely by region and facility (dealer vs independent shop).
- Condition of related components: If rotors, brakes, or wheel bearings in nearby hubs show wear, a shop may bundle or suggest additional services.
- Time required for installation: If the hub is difficult to access or if a rotor has to be machined or pressed, labor time may be longer.
To get an accurate quote, obtain multiple estimates and ask what is included in the price (parts warranty, alignment, taxes, disposal fees, and whether ABS sensors are covered).
What to expect during service
When you bring your CR-V in, a typical service flow looks like this: the mechanic confirms which axle needs the hub, inspects related components (brakes, rotors, and ABS wiring), removes the wheel, caliper, and rotor as needed, replaces the hub assembly, and tests the wheel for play and the ABS function. If a rotor or brake system part is worn, the shop may recommend replacing or resurfacing it at the same time, which can add to the total cost. Depending on the shop, an alignment check after replacement may also be offered or required.
Summary
For a 2008 Honda CR-V, a wheel bearing/hub replacement generally falls in the $300–$700 range, with front-hub jobs tending to be more expensive than rear-hub jobs and AWD configurations pushing costs higher. Parts choice, labor rates, ABS sensor integration, and any additional brake or alignment work all influence the final price. The best approach is to gather quotes from several shops, confirm exactly what is included, and consider both short-term cost and long-term reliability when choosing parts and service plans.
Can I drive a car with a bad wheel bearing?
No. It is not safe to drive with a bad wheel bearing. A broken wheel bearing can seize, overheat, or even cause the wheel to detach completely.
How much is a 2008 Honda CR-V worth today?
The value of a used 2008 Honda CR-V ranges from $1,393 to $4,747, based on vehicle condition, mileage, and options. Get a free appraisal here.
How much to fix wheel bearing on Honda CRV?
between $390 and $603
The average cost for a Honda CR-V Wheel Bearing Replacement is between $390 and $603 but can vary from car to car.
Which CRV year to stay away from?
The first CR-V of the 21st century sees an increase in engine-related issues and the beginning of a series of recalls for defective airbags (the notorious Takata airbag recall). The recall affected numerous model years (mostly 2002-2015), so always check this out if you're buying a used CR-V.