The 2019 Mitsubishi Outlander with a 2.4-liter engine takes about 4.5 quarts of engine oil when you change the oil and filter, and roughly 4.0 quarts if you drain the oil but do not replace the filter. This aligns with Mitsubishi’s service data and typical maintenance manuals. Always check your owner's manual for the exact figure tied to your vehicle's trim and production date.
Official capacity and what it means
Oil capacity data is typically presented in service information as two figures: with the oil filter and without the filter. For the 2019 Outlander 2.4L, the standard values are:
- With filter: 4.5 quarts (4.3 L)
- Without filter: 4.0 quarts (3.8 L)
When performing an oil change, use the “with filter” quantity as the target and verify the level on the dipstick after refilling.
In practice, plan for about 4.5 quarts and then adjust based on the dipstick reading to reach the correct level on the oil gauge.
Practical steps for an oil change
Here are the standard steps to complete a routine oil change on the Outlander 2.4L:
- Warm up the engine briefly, then park on level ground and turn off the engine.
- Lift the front of the vehicle safely and place a drain pan beneath the oil sump.
- Remove the drain plug and allow the old oil to drain completely.
- Remove and replace the oil filter with a new one, applying a light coat of oil to the gasket.
- Reinstall the drain plug and pour in the recommended amount of oil (typically 4.5 quarts with filter).
- Start the engine, check for leaks, and use the dipstick to confirm the oil level is within the proper range; add more oil if needed and dispose of the old oil properly.
After completing the oil change, reset any maintenance reminders if applicable and ensure the used oil is recycled at an appropriate facility.
Oil grade recommendations
Using the right oil viscosity and specification is important for engine longevity. For the 2.4L Outlander, Mitsubishi generally recommends 0W-20 full-synthetic oil. If 0W-20 is not available or in certain climates, some operators may use 5W-30, but it is best to follow the owner's manual or consult a dealer for your region.
Recommended options include:
- 0W-20 full synthetic API SN/ILSAC GF-5 or newer
- 5W-30 full synthetic API SN/ILSAC GF-5 (only if specified by your manual or dealer)
Always confirm the exact grade and specification in your manual and replace the oil filter during changes to maintain proper engine protection.
Summary
For the 2019 Mitsubishi Outlander with a 2.4L engine, plan to have about 4.5 quarts of oil in the system when performing an oil change with a new filter, or about 4.0 quarts if the filter is not replaced. Verify the level with the dipstick after refilling and follow Mitsubishi’s guidance on the correct oil type and change intervals to keep the engine running smoothly.
What are the common repairs for outlanders?
Mitsubishi Outlander Common Problems New York Drivers Should Know
- Transmission hesitation or jerking in certain driving conditions.
- Engine roughness or stalling after high mileage.
- AC not working during the hot summer months.
- Electrical issues such as malfunctioning lights or sensors.
What kind of oil does a Mitsubishi Outlander 2.4 take?
Most current Outlander models require 0W-20 full synthetic oil, with capacity ranging from 4.2 to 4.8 quarts depending on engine size. The Outlander Sport 2.4L engine may specify 5W-30.
How much oil does a 2019 Mitsubishi Outlander 2.4 L take?
The 2019 Mitsubishi Outlander Sport takes 4.8 quarts of oil.
What kind of oil do I need for a 2019 Mitsubishi Outlander?
0W-20 Synthetic. 5W-20/5W-30 Conventional Grades.