The battery in most 2013 Honda key fobs is a CR2032 coin cell. Replacing it involves opening the fob, swapping in a fresh battery, and snapping the unit back together. The whole process is quick and can be done at home with basic tools.
Identify the right battery and what you’ll need
Before you start, confirm the battery type and gather a few simple tools so you can work cleanly.
- Battery type: CR2032, 3V coin cell (most 2013 Honda remotes use this). If your fob shows a different label, check the inside of the case or your vehicle manual.
- Tools: a small flat-head screwdriver or a coin for prying, and a clean workspace. Optional gloves to avoid leaving fingerprints.
Having the correct battery and tools on hand helps the replacement go smoothly and reduces the chance of damaging the fob.
Step-by-step replacement
Follow these steps to replace the battery in a typical 2013 Honda key fob. Take care to keep parts clean and aligned as you work.
- Remove the emergency key blade: on the back of the fob, slide the small latch and pull out the metal key.
- Open the fob: use a small flat-head screwdriver or a coin to gently pry apart the two halves along the seam. Work slowly to avoid snapping the housing.
- Locate and remove the old battery: note the orientation of the battery (which side is up). Use a nonmetallic tool if possible to lift it out.
- Insert the new battery: place the CR2032 with the correct orientation, typically with the + side facing up toward you.
- Reassemble the fob: snap the two halves back together firmly and reinsert the emergency key blade.
- Test the fob: press the buttons to confirm that lock, unlock, and trunk functions respond from a short distance.
After reassembling, test the remote range and button presses to ensure everything works correctly. If a button doesn’t respond, double-check battery orientation and that the halves are fully snapped together.
Tips and cautions
These pointers can help prevent common issues during and after replacement.
- Use a fresh CR2032 battery and avoid touching the battery’s contacts with your bare fingers; oils can affect contact.
- Do not force the fob halves together; if they don’t snap easily, reopen and reseat the battery or gasket seal.
- If your fob doesn’t work after replacement, verify the battery orientation and that you reinserted the mechanical key correctly. Some functions can be sensitive to proximity until you’re near the car.
- Most 2013 Honda fobs do not require reprogramming after a battery change. If you encounter ongoing issues, consult your owner’s manual or contact a Honda dealer for guidance.
With the proper battery installed and the housing securely reassembled, your key fob should regain full function without additional steps.
Summary
Changing the battery in a 2013 Honda key fob is a straightforward DIY task. Identify a CR2032 battery, gather a small flat-head screwdriver or coin, and carefully pry the case apart to replace the coin cell. Reassemble the fob, test its functions, and you should be back to normal in a few minutes.
How to open Honda key remote to change battery?
So. And you can see there's two halves. Here. We can get rid of the other half and then here is the battery. Now you'll notice that the battery is hooked in on this side.
How to reset Honda Accord key fob?
How to Reprogram Your Honda Key Fob
- Enter the car and shut all of the doors.
- Turn the key to the “on” position.
- Press and hold the “lock” or “unlock” button and wait to make sure the door is cycling through correctly, meaning the key fob has completed the programming cycle.
Can I still start my Honda with a dead key fob battery?
Completely out of the key fob So no battery in this key fob You simply take the key fob put your foot on the brake. Put the key fob up against the power. Button press it once.
How do you program a key fob for a 2016 Honda Civic?
Press the Program Button
Press the “LOCK” button on your key fob. Then, within five seconds, press and hold the “UNLOCK” button on the fob for about one second before releasing it. This should trigger the vehicle to enter programming mode. The vehicle's hazard lights will blink to confirm the process.